Replacing Toner Cartridge | Toshiba e-STUDIO203 specification

5 TROUBLESHOOTING

Replacing Toner Cartridge

When the toner in the toner cartridge has run out, replace the toner cartridge following the pro- cedure below.

yBefore inserting a new toner cartridge, check the product name of the cartridge. If you can see “T-1640”, this cartridge is usable.

yDo not dispose of used toner cartridges. Contact your service representative.

yDo not touch the parts on the circuit board mounted on the toner cartridge because they may be damaged.

Never attempt to incinerate toner cartridges. This could cause an explosion.

1 Open the front cover.

2 Hold down the green lever.

90 Replacing Toner Cartridge

Image 92

Toshiba e-STUDIO203 manual Replacing Toner Cartridge, Open the front cover, Hold down the green lever

Contents

Operators Manual for Copying Functions EPA Energy Star MFD For EU only For Germany onlyPage Lineup of Our Manuals Operator’s Manual for Copying Functions Precautions in this manual Before Reading This Manual Description of original/paper direction Trademarks Before Reading This Manual Contents Copying in Same Page Order as Originals Sort Copying 100 111 Index Contents Toshiba Quality is Second to None Recommended toner cartridgesCartridge detecting function Toner remaining check function General Supplies / PartsToner Ecological energy-saving design Features of e-STUDIO163/203Functions extended by various options General Precautions When installing or moving Other points 10 cm 80 cm When using the equipment Position of Certification label, etc During maintenance or inspection When handling supplies Disclaimer Notice Poration Disclaimer Notice Preparation 2 Placing Copy Paper Preparation 1 Turning Power onDescription of Each Component Description of Each Component Front / Right sidePlaten Cover Automatic Document Feeder optional, MR-2017 Left side / Inner side USB terminal 4-pin Receiving tray Scanning areaOriginal scale Platen sheet Configuration of options Control panel Original mode button/lamps Density adjustment buttons/lampsLED display Copy qty. / zoom display selecting button/lamp Original setting lamp Drawer button/lampsCopy button/lamps Original button/lamps Turning power OFF Preparation 1 Turning Power onTurning power on Cancelling the energy saving mode Saving energy when not in use Energy saving modeTo turn the equipment into the energy saving mode manually Feeder Media type Paper size Maximum sheet Capacity *1 Preparation 2 Placing Copy PaperAcceptable media types Recommended paper Paper types not acceptableStoring paper Media type Product name Placing paper in drawers Press down the paper plate Widen the gap with both hands Adjust the side guides to the desired paper size Place paper in the drawer Do not let your fingers be caught when closing the drawer Register the paper size into the equipment Preparation 3 Registering Size of Paper Placed Registering standard size A3, A4, A4-R, A5-R, B4 Registering other standard sizes Code No Preparation 3 Registering Size of Paper Placed Press the Start button Making Copies Using Bypass TrayPlacing Originals When the built-in memory has become full during scanning Setting position Type of origiPlacing Originals Acceptable originals Placing originals on the original glass Placing booklet-type originals such as books or catalogues Using Automatic Document Feeder optional Precautions for Automatic Document Feeder optionalWhen black streaks appear on the copied image Maximum number Paper weight When placing a large amount of originals with a long width Placing originals on Automatic Document Feeder optional Making Copies Check if paper is placed in the drawerPlace the original Select the copy modes as required When the number of sheets exiting has exceeded When the paper has run outStopping/Resuming copying Press the CLEAR/STOP button during scanning or copying Interrupting copying and making another copy Interrupt copy Press the Interrupt button Using Bypass Tray Media type Paper size Maximum sheet Capacity *1 Preparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Using Bypass Tray Automatic paper selection APS Manual paper selection Default Settings Paper SelectionZooming In/Out Copy Image Default Settings Contents Default setting at installation Paper Selection Automatic paper selection APSPlace the original on the Automatic Document Feeder Automatic paper selection APS Manual paper selection Place paper in the drawer Place the original Selecting the drawer of the equipment Zooming In/Out Copy Image Automatic magnification selection AMSAutomatic magnification selection AMS Specifying reproduction ratio manually If the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Desired reproduction ratio appears Specifying reproduction ratio manuallyPress Zooming out or Zooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode Adjusting Density Level To adjust the density to the desired levelTo return it to the automatic copy density mode Dark Adjusting Density Level Settings and Management Equipment Switching Operation Sound On/Off All lamps on Sound on All lamps off Sound off Press Button for more than two seconds Switch the display to check the rest of the total numberChecking Total Number Copied Checking Total Number Copied Troubleshooting When Message Lamp is Lit/Blinking Paper Jams When Message Lamp is Lit/Blinking Cover open lampPaper empty lamp Toner lamp Recommended toner cartridges Service call lamp Paper jam lamp Checking position of paper jams When paper jams occur frequentlyPaper Jams When releasing jammed paper Paper jams within Automatic Document Feeder optionalRaise the lever, and then open the upper cover Do not tear jammed paper Paper Jams Paper jams on bypass tray Pull out the paper jammed on the bypass tray Paper jam behind transfer unit Close the transfer unit and the side cover Paper jams within fuser unit Open the transport guide while holding the knob a Release the jammed paper Paper jams within Paper Feed Unit optional Hold down the green lever Replacing Toner CartridgeOpen the front cover Pull out the toner cartridge Open the side cover Clean the chargerInsert the toner cartridge along the rail With the transfer charger wire Equipment starts supplying toner Phenomenon Usual cause Countermeasure Before Calling Service TechnicianGeneral operation Toner-related items Original/Copy paper-related items Image trouble Tion Charger is dirty Clean the charger Maintenance and Inspection Daily Inspection 100 Daily Inspection Original glass Guides Platen sheet Cleaning charger Open the front cover Clean the charger Cleaning transfer charger Daily Inspection Daily Inspection Specifications and Options STUDIO163/203 Specifications OPC Continuous copying speed Paper size Feeder STUDIO163 STUDIO203 Paper Feed Unit Specifications of OptionsAutomatic Document Feeder Packing List Packing List Index AMS APS 106 DP-1640/2030 OME050129B0 Multifunctional Digital Systems