Insert the toner cartridge along the rail | Toshiba e-STUDIO203

5 TROUBLESHOOTING

6 Insert the toner cartridge along the rail.

yBefore inserting the toner cartridge, check if the green lever is raised and raise it if not.

yInsert the toner cartridge until you hear a click sound.

7 Clean the charger.

Hold the cleaning knob of the charger and pull it out toward you carefully until it comes to a stop. Then reinsert it in its original position carefully. Repeat this procedure two or three times.

Check if the cleaning knob is fully inserted after cleaning.

8 Open the side cover.

92 Replacing Toner Cartridge

Image 94

Toshiba e-STUDIO203 manual Insert the toner cartridge along the rail, Clean the charger, Open the side cover

Contents

Operators Manual for Copying Functions EPA Energy Star MFD For EU only For Germany onlyPage Lineup of Our Manuals Operator’s Manual for Copying Functions Precautions in this manual Before Reading This Manual Description of original/paper direction Trademarks Before Reading This Manual Contents Copying in Same Page Order as Originals Sort Copying 100 111 Index Contents Cartridge detecting function Toshiba Quality is Second to NoneRecommended toner cartridges Toner remaining check function Toner Supplies / PartsGeneral Functions extended by various options Features of e-STUDIO163/203Ecological energy-saving design General Precautions When installing or moving Other points 10 cm 80 cm When using the equipment Position of Certification label, etc During maintenance or inspection When handling supplies Disclaimer Notice Poration Disclaimer Notice Description of Each Component Preparation 1 Turning Power onPreparation 2 Placing Copy Paper Platen Cover Description of Each ComponentFront / Right side Automatic Document Feeder optional, MR-2017 Left side / Inner side Original scale USB terminal 4-pinReceiving tray Scanning area Platen sheet Configuration of options Control panel LED display Original mode button/lampsDensity adjustment buttons/lamps Copy qty. / zoom display selecting button/lamp Copy button/lamps Original setting lampDrawer button/lamps Original button/lamps Turning power on Preparation 1 Turning Power onTurning power OFF To turn the equipment into the energy saving mode manually Saving energy when not in use Energy saving modeCancelling the energy saving mode Acceptable media types Preparation 2 Placing Copy PaperFeeder Media type Paper size Maximum sheet Capacity *1 Storing paper Recommended paperPaper types not acceptable Media type Product name Placing paper in drawers Press down the paper plate Widen the gap with both hands Adjust the side guides to the desired paper size Place paper in the drawer Do not let your fingers be caught when closing the drawer Register the paper size into the equipment Preparation 3 Registering Size of Paper Placed Registering standard size A3, A4, A4-R, A5-R, B4 Registering other standard sizes Code No Preparation 3 Registering Size of Paper Placed Press the Start button Placing Originals Using Bypass TrayMaking Copies Placing Originals When the built-in memory has become full during scanningSetting position Type of origi Acceptable originals Placing originals on the original glass Placing booklet-type originals such as books or catalogues When black streaks appear on the copied image Using Automatic Document Feeder optionalPrecautions for Automatic Document Feeder optional Maximum number Paper weight When placing a large amount of originals with a long width Placing originals on Automatic Document Feeder optional Place the original Making CopiesCheck if paper is placed in the drawer Select the copy modes as required Stopping/Resuming copying When the number of sheets exiting has exceededWhen the paper has run out Press the CLEAR/STOP button during scanning or copying Interrupting copying and making another copy Interrupt copy Press the Interrupt button Using Bypass Tray Media type Paper size Maximum sheet Capacity *1 Preparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Using Bypass Tray Zooming In/Out Copy Image Default Settings Paper SelectionAutomatic paper selection APS Manual paper selection Default Settings Contents Default setting at installation Place the original on the Automatic Document Feeder Paper SelectionAutomatic paper selection APS Automatic paper selection APS Manual paper selection Place paper in the drawer Place the original Selecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manually If the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Press Zooming out or Specifying reproduction ratio manuallyDesired reproduction ratio appears Zooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode To return it to the automatic copy density mode Adjusting Density LevelTo adjust the density to the desired level Dark Adjusting Density Level Settings and Management Equipment Switching Operation Sound On/Off All lamps on Sound on All lamps off Sound off Checking Total Number Copied Switch the display to check the rest of the total numberPress Button for more than two seconds Checking Total Number Copied Troubleshooting When Message Lamp is Lit/Blinking Paper Jams Paper empty lamp When Message Lamp is Lit/BlinkingCover open lamp Toner lamp Recommended toner cartridges Service call lamp Paper jam lamp Paper Jams When paper jams occur frequentlyChecking position of paper jams Raise the lever, and then open the upper cover When releasing jammed paperPaper jams within Automatic Document Feeder optional Do not tear jammed paper Paper Jams Paper jams on bypass tray Pull out the paper jammed on the bypass tray Paper jam behind transfer unit Close the transfer unit and the side cover Paper jams within fuser unit Open the transport guide while holding the knob a Release the jammed paper Paper jams within Paper Feed Unit optional Open the front cover Replacing Toner CartridgeHold down the green lever Pull out the toner cartridge Insert the toner cartridge along the rail Clean the chargerOpen the side cover With the transfer charger wire Equipment starts supplying toner General operation Before Calling Service TechnicianPhenomenon Usual cause Countermeasure Toner-related items Original/Copy paper-related items Image trouble Tion Charger is dirty Clean the charger Maintenance and Inspection Daily Inspection 100 Daily Inspection Original glass Guides Platen sheet Cleaning charger Open the front cover Clean the charger Cleaning transfer charger Daily Inspection Daily Inspection Specifications and Options STUDIO163/203 Specifications OPC Continuous copying speed Paper size Feeder STUDIO163 STUDIO203 Automatic Document Feeder Specifications of OptionsPaper Feed Unit Packing List Packing List Index AMS APS 106 DP-1640/2030 OME050129B0 Multifunctional Digital Systems