Paper jams within fuser unit | Toshiba e-STUDIO203 guide

Paper jams within fuser unit

yBe careful not to let your fingers be caught between the equipment and the side cover. This could injure you.

yDo not touch the fuser unit or the metal part around the unit.

This could cause burns, or injury to your hands if you touch the inside of the equipment.

1Open the side cover, and then lay down the transfer unit. Then press down the two fuser pressure release levers (green) until they come to a stop.

Press down the levers fully until they stop.

2 Open the transport guide while holding the knob (A).

A

Paper Jams 87

Image 89

Toshiba e-STUDIO203 manual Paper jams within fuser unit, Open the transport guide while holding the knob a

Contents

Operators Manual for Copying Functions EPA Energy Star MFD For Germany only For EU onlyPage Operator’s Manual for Copying Functions Lineup of Our Manuals Before Reading This Manual Precautions in this manual Trademarks Description of original/paper direction Before Reading This Manual Contents 100 Copying in Same Page Order as Originals Sort Copying Index 111 Contents Recommended toner cartridges Toshiba Quality is Second to NoneCartridge detecting function Toner remaining check function General Supplies / PartsToner Ecological energy-saving design Features of e-STUDIO163/203Functions extended by various options When installing or moving General Precautions 10 cm 80 cm Other points When using the equipment Position of Certification label, etc When handling supplies During maintenance or inspection Poration Disclaimer Notice Disclaimer Notice Preparation 2 Placing Copy Paper Preparation 1 Turning Power onDescription of Each Component Front / Right side Description of Each ComponentPlaten Cover Automatic Document Feeder optional, MR-2017 Left side / Inner side Receiving tray Scanning area USB terminal 4-pinOriginal scale Platen sheet Configuration of options Control panel Density adjustment buttons/lamps Original mode button/lampsLED display Copy qty. / zoom display selecting button/lamp Drawer button/lamps Original setting lampCopy button/lamps Original button/lamps Turning power OFF Preparation 1 Turning Power onTurning power on Cancelling the energy saving mode Saving energy when not in use Energy saving modeTo turn the equipment into the energy saving mode manually Feeder Media type Paper size Maximum sheet Capacity *1 Preparation 2 Placing Copy PaperAcceptable media types Paper types not acceptable Recommended paperStoring paper Media type Product name Press down the paper plate Placing paper in drawers Widen the gap with both hands Place paper in the drawer Adjust the side guides to the desired paper size Register the paper size into the equipment Do not let your fingers be caught when closing the drawer Registering standard size A3, A4, A4-R, A5-R, B4 Preparation 3 Registering Size of Paper Placed Code No Registering other standard sizes Preparation 3 Registering Size of Paper Placed Press the Start button Making Copies Using Bypass TrayPlacing Originals Setting position Type of origi When the built-in memory has become full during scanningPlacing Originals Acceptable originals Placing originals on the original glass Placing booklet-type originals such as books or catalogues Precautions for Automatic Document Feeder optional Using Automatic Document Feeder optionalWhen black streaks appear on the copied image Maximum number Paper weight Placing originals on Automatic Document Feeder optional When placing a large amount of originals with a long width Check if paper is placed in the drawer Making CopiesPlace the original Select the copy modes as required When the paper has run out When the number of sheets exiting has exceededStopping/Resuming copying Press the CLEAR/STOP button during scanning or copying Press the Interrupt button Interrupting copying and making another copy Interrupt copy Media type Paper size Maximum sheet Capacity *1 Using Bypass Tray Preparation Registering paper size placed on bypass tray ST-R Folio Comp Using Bypass Tray Press the Start button Bypass copying on standard size paper Placed on the bypass tray is lit Using Bypass Tray Using Bypass Tray Automatic paper selection APS Manual paper selection Default Settings Paper SelectionZooming In/Out Copy Image Contents Default setting at installation Default Settings Automatic paper selection APS Paper SelectionPlace the original on the Automatic Document Feeder Automatic paper selection APS Place paper in the drawer Place the original Manual paper selection Selecting the drawer of the equipment Automatic magnification selection AMS Zooming In/Out Copy ImageAutomatic magnification selection AMS Specifying reproduction ratio manually If the Function Clear lamp is blinking and copying stops Specifying both the sizes of the original and the copy paper Desired reproduction ratio appears Specifying reproduction ratio manuallyPress Zooming out or Zooming In/Out Copy Image Copying in Same Page Order as Originals Sort Copying Selecting Image Mode To adjust the density to the desired level Adjusting Density LevelTo return it to the automatic copy density mode Dark Adjusting Density Level Settings and Management Equipment All lamps on Sound on All lamps off Sound off Switching Operation Sound On/Off Press Button for more than two seconds Switch the display to check the rest of the total numberChecking Total Number Copied Checking Total Number Copied When Message Lamp is Lit/Blinking Paper Jams Troubleshooting Cover open lamp When Message Lamp is Lit/BlinkingPaper empty lamp Toner lamp Recommended toner cartridges Paper jam lamp Service call lamp Checking position of paper jams When paper jams occur frequentlyPaper Jams Paper jams within Automatic Document Feeder optional When releasing jammed paperRaise the lever, and then open the upper cover Do not tear jammed paper Paper Jams Pull out the paper jammed on the bypass tray Paper jams on bypass tray Paper jam behind transfer unit Close the transfer unit and the side cover Open the transport guide while holding the knob a Paper jams within fuser unit Release the jammed paper Paper jams within Paper Feed Unit optional Hold down the green lever Replacing Toner CartridgeOpen the front cover Pull out the toner cartridge Open the side cover Clean the chargerInsert the toner cartridge along the rail With the transfer charger wire Equipment starts supplying toner Phenomenon Usual cause Countermeasure Before Calling Service TechnicianGeneral operation Original/Copy paper-related items Toner-related items Image trouble Tion Charger is dirty Clean the charger Daily Inspection 100 Maintenance and Inspection Original glass Guides Platen sheet Daily Inspection Open the front cover Clean the charger Cleaning charger Cleaning transfer charger Daily Inspection Daily Inspection Specifications and Options OPC STUDIO163/203 Specifications Paper size Feeder STUDIO163 STUDIO203 Continuous copying speed Paper Feed Unit Specifications of OptionsAutomatic Document Feeder Packing List Packing List AMS APS Index 106 DP-1640/2030 OME050129B0 Multifunctional Digital Systems