Sync, Option | Toshiba ik-tf7u specs

(4. 5) Changing the shading correction mode

1Move the "→" to SHAD. by pushing [MENU UP], [MENU DOWN] buttons.

2Select the SHAD. by pushing [DATA UP], [DATA DOWN] buttons.

Note: The alignment value for shading is fixed to "0" when selecting SHAD. OFF. MANU is not dis- played in the menu.

(4. 6) Changing the manual shading correction setting

1Move the "→" to MANU by pushing [MENU UP], [MENU DOWN] buttons.

2Adjust the MANUAL SHADING by pushing [DATA UP], [DATA DOWN] buttons.

( 5 ) SYNC

When an external sync signal is input, the display menu changes from INT (internal sync) to EXT (external sync) automatically.

Move up down

Select the desired

by pushing

value by pushing

MENU UP, DOWN

DATA UP, DOWN

-- SYNC --

MODE

EXT

H PHASE

0

•Sync system display

•H PHASE adjustment -100 to 100

(5. 1) Adjusting horizontal phase

1Move the "→" to H PHASE by pushing [MENU UP], [MENU DOWN] buttons.

2Adjust the horizontal phase by pushing [DATA UP], [DATA DOWN] buttons.

( 6 ) OPTION

(6. 1) Changing serial communication baud rate

1Move the "→" to BAUD RATE by pushing [MENU UP], [MENU DOWN] buttons.

2Select either 9600 or 19200 by pushing [DATA UP], [DATA DOWN] buttons.

Move up down by pushing

MENU UP, DOWN

Select the desired value by pushing

DATA UP, DOWN

-- OPTION --

BAUD RATE 9600

• Serial baud rate setting 9600, 19200

23

Image 23

Toshiba ik-tf7u instruction manual Sync, Option

Contents

Following information is only for EU-member states IK-TF7U Safety Precautions Avoid placing in humid, smoky, vaporized or dusty places Disclaimer Table of Contents Components Names and Functions Standard Connection Connector Pin AssignmentsConnection White Balance OperationAutomatic Black Balance Temp LOW Result displayed Meaning OFF GainShading Correction Available selections Items Controlled by the Screen Display Using the Menus Mode Setting by the Screen Display Flicker may be large MenusShutter Electronic shutter Manual Menu UP, Down Data UP, Down Changing the setting in Manu modeMode = Manual Partial scanning setting Changing the shutter speed setting Changing the setting in SS synchro. scan modeMode = SS Changing 1P SNR exposure time setting Changing the setting in E.TRG modeChanging the setting in 1P SNR mode Changing the polarity of inputting trigger pulse setting Changing 1P SR exposure time setting Changing the setting in 1P SR modeMode = E.TRG E.TRG = 1P SR Mode = E.TRG E.TRG = PW SNR Changing the setting in PW SNR mode Mode = E.TRG E.TRG = RR Changing the setting in PW SR modeMode = E.TRG E.TRG = PW SR Gain Video gain Changing the setting in GainChanging the gain in Manu mode WHT BAL White balance Changing R pedestal MANU/OFFChanging gamma correction Changing master pedestal Option Sync Synchro. Scan Operation Setting by the frameReturning to factory settings Setting by 1H Fval Lval Dval 1P SNR 1 Pulse Trigger Sync Non Reset1 Pulse Trigger SYNC-NON Reset Picture Output Timing E. TRG External trigger 1 Pulse Trigger SYNC-RESET Picture Output Timing 1P SR 1 Pulse Trigger Sync Reset Pulse Width Trigger SYNC-NON Reset Picture Output Timing PW SNR Pulse width trigger SYNC-NON Reset 1 Pulse Width Trigger SYNC-RESET Picture Output Timing PW SR Pulse width trigger SYNC-RESET Long Term Exposure RR Reset restartInput Timing Chart Example Partial Scanning on When Partial Scanning Mode is onPartial Read Partial Scanning OFF All pixels scanning External sync frequency range External sync signal polarityUsing the unit with external sync signal External Sync Input Output Signal Specificatoins Vertical Output Waveform Timing Chart Output Waveform Timing ChartHorizontal Output Waveform Timing Chart RGB, 3CCD Specifications Symptom Items to be checked External Appearance DiagramBefore Making a Service Call Your Responsibilities Limited Warranty Toshiba CCD CameraOne 1 Year Limited Warranty of Labor and Parts How to Obtain Warranty Service Step-By-Step Procedures