Signal Levels of INPUT/OUTPUT Terminals

NOTICE

SIGNAL LEVELS OF INPUT/OUTPUT TERMINALS

Input/Output terminal		Signal level	Additional remarks
	Open				DC5V
					DC5V
ALARM IN	Ground input			10K	10K
				10K
			100	10K
	0V	± 0.5V	100	10K
	0V	± 0.5V	IN
		200 ms or greater	GND	0.001μ	10K
		200 ms or greater		0.001μ	10K
	Open				DC5V
				10K	10K
	Ground input			10K
ALARM RESET	Ground input		100	10K
ALARM RESET	0V	± 0.5V	RESET
	0V	± 0.5V	RESET
			GND	0.001μ	10K
		200 ms or greater		0.001μ	10K
		200 ms or greater

		Alarm recording	DC5V
			220
ALARM OUT		5V output	OUT
ALARM OUT		5V output	10
		Output impedance	GND
	0V	Output impedance
	0V	230 Ohm : MAX 10mA
		230 Ohm : MAX 10mA

	5V				DC5V
	5V				2.2K
	a: 20 ms				2.2K
	a: 20 ms				OUT
REC TRIGG. OUT	(SPA2, EPA6)				OUT
REC TRIGG. OUT	(SPA2, EPA6)	0V		Output impedance	220
	a: 32 ms	0V			GND
	a: 32 ms				GND
	(Except SPA2, EPA6)		a	220 Ohm : MAX 10mA
	(See page 38.)		a
	(See page 38.)

Open	Tape end
	TAPE END
TAPE END OUT	220
	GND

	Short	Output impedance
	approx. 2 seconds.	220 Ohm : MAX 20mA
	approx. 2 seconds.
	Open			DC5V
EXT CONT. IN			10K	10K
			10K
	Ground input	100	10K
	0V ± 0.5V	IN
	0V ± 0.5V
		GND	0.001μ	10K
	200 ms or greater		0.001μ	10K
	200 ms or greater

INTRODUCTION

PREPARATION

RECORDING

OPERATION

PLAYBACK

OPERATION

NOTICE

Page 45

Image 45

Toshiba kV-9960A Signal Levels of INPUT/OUTPUT Terminals, Input/Output terminal Signal level Additional remarks

Contents

Instruction Manual Please Read Important Precautions Power Sources Important Safety InstructionsRadiators, heat registers, stoves Unplug this product from the wall Power Lines AccessoriesWhen the power-supply cord or plug is damaged To restore the product to its normal operation Table of Contents Features Front Panel Instructions in Brief Tape Remain button Time Mode / SET + buttonsCassette Compartment Display button Rear Panel Specification of Battery Word on the Exclusive 3N-100AAS Battery PackInstallation Removal VCR Display REW button Press to start play backFF button Connection with a Video Camera Connections Video Typical Connection with the Sequential SwitcherTo REC TRIGG. OUT Output Contents of Screen Display Alarm Recall Screen Operation Setting the Clock Date-Time Display ON-SCREEN FunctionsVCR display Monitor screen Display Screen Is pressed. When an alarm is Alarm numberChanges to the alarm number This function enables to indicate and record information When the tape reaches Alarm MemoryCounter Displays Counter Memory Regarding the error code E-6 Display Error MessageTape Remain Code Number Condition of Abnormality Setting the RECORDING/PLAY Back Time HOW to Operate 24 Hour Virtual Real Time ModeMode display Loading and Unloading a Video Cassette Loading a CassetteUnloading a Cassette Camera and monitor TV Not been removed Recording Restart Recording Setting the Restart Recording Setting the Timer Program Timer RecordingDaily Timer Recording Program Screen Press the Timer button Time Mode button is pressed, the displayShould be more than 1 minute. If they are same, timer During timer power off mode, alarm recording will not Weekly Timer Recording Press the Shift ButtonGRAM.to blink PROPress the Shift Button to blink the MO1 start time Example Overlapping ProgramsFR2 DLY Operation at Alarm Input Alarm RecordingAlarm Recall Display Event Recording Connecting the Alarm Terminals Display Recording time Setting the Alarm RecordingCont Manual Auto Recording Connecting the External control terminalOperation of Auto Recording Auto recording How to Forbid Auto Recording How to Release Auto RecordingPress Timer button to release the timer mode Press the + or SET Setting contents Buzzer Screen display Counter display How to Set to Stop at End of TapeOperation After Tape END Detection Display Operation after detection of tape end How to Set to Auto Rewind at End of Tape Alarm recording does not operate during auto-rewindMenu Screen ButtonREC. to select REW → How to Set to Repeat Record at End of Tape Connection with the Sequential Switcher Recording with the Sequential SwitcherTiming for Camera Switching C D a B C D Press the Shift REC Trigger Output Selection in the Alarm RecordingButton to set the REC Trigger SEL Tracking Adjustment Recording time mode Time mode for playbackPlayback REW Stop Using the Shuttle DialPicture Search Play Slow Still Play Playback in Various Modes Time Date Search Search OperationPress the SET button to Set the Minute to Alarm Search Alarm M to lightStill picture mode Press the Play button Input/Output terminal Signal level Additional remarks Signal Levels of INPUT/OUTPUT Terminals Press the or Time Mode button to go to SPA2 mode Check the playback picture recorded in SPA2 modeDaily and Periodic Inspection Order of Daily Checks Steps to Take after Daily Checks Request for Periodic ChecksTape Usage Frequency Dew Condensation Installation Before Calling Service PersonnelFunction/Operation Recording Other matters Playback Connector section SpecificationsAccessories Dew caution sheet 70971826 Limited Warranty

Toshiba kV-9960A instruction manual Signal Levels of INPUT/OUTPUT Terminals

Models: kV-9960A

SIGNAL LEVELS OF INPUT/OUTPUT TERMINALS

Input/Output terminal

Signal level

Additional remarks

REC TRIGG. OUT