Specifications, Connector section, Accessories | Toshiba kV-9960A

SPECIFICATIONS

Power supply	120V AC, 60 Hz

Power consumption	18W
External dimensions	17 × 3-5/8 × 12-1/2 inch (W × H × D), 430 × 92 × 318 mm (W × H × D)

Weight	11 lbs (5.0 kg)

Signal system	Standard NTSC color television system

Recording System	Rotary 2-head azimuth

Cassette	VHS marked, 1/2 inch cassette tape
Tape speed	SPA2 mode: 33.35mm/s, EPA6 mode: 11.12mm/s

Recording/playback time mode	SP modes: A2, A12, A24, 24, 48, 72, 120, 168, 240, 480, 720, 960
	EP modes: A6, A18, 30, 48, 72, 120, 168, 240, 480, 720, 960

Fast forward/rewind time	Within 2 minutes (when T-120 is used)

Video input (BNC)	1.0V(p-p), 75 Ω Unbalanced Luminance signal

Video output (BNC)	1.0V(p-p), 75 Ω Unbalanced Luminance signal

Horizontal resolution	350 lines (monochrome mode), 300 lines (color mode) (SPA2 mode)
Video S/N	More than 45 dB: monochrome mode (SPA2 mode)
	More than 45 dB: color mode (SPA2 mode)

Audio input	Line input: 308mV (rms), more than 47k Ω, pin jack
	Microphone input: 0.245mV (rms), less than 5k Ω, ø3.5 jack

Audio output	388mV (rms), less than 4.7k Ω, pin jack

No. of audio tracks	1 track
Audio frequency characteristics	100 Hz to 10 kHz (SPA2 mode)

Audio S/N	More than 43 dB (SPA2 mode)

Operating conditions	Temperature: 41°F to 104°F (5°C to 40°C)
	Humidity: less than 80%

Storage conditions	–4°F to 140°F (–20°C to 60°C)

Connector section

Alarm input	Ground input: 0 to 0.5V

Alarm reset input	Ground input: 0 to 0.5V

Alarm output	DC 5V, impedance: 230 Ω, less than 10mA

Recording trigger output	During time lapse: 0/5V negative pulse signal
	SPA2 and EPA6 mode: 0V
	Alarm recording: 0/5V (Programmable)
	Except above-mentioned: 5V

Tape end output	Open/Short, impedance: 220 Ω, less than 20mA

External control input	Ground input: 0 to 0.5V

Design and specifications are subject to change without notice.

Accessories
• Instruction manual	(1)
• Dew caution sheet	(1)

INTRODUCTION

PREPARATION

RECORDING

OPERATION

PLAYBACK

OPERATION

NOTICE

50

Image 51

Toshiba kV-9960A instruction manual Specifications, Connector section, Accessories, Dew caution sheet

Contents

Instruction Manual Please Read Important Precautions Unplug this product from the wall Important Safety InstructionsPower Sources Radiators, heat registers, stoves To restore the product to its normal operation AccessoriesPower Lines When the power-supply cord or plug is damaged Table of Contents Features Front Panel Instructions in Brief Display button Time Mode / SET + buttonsTape Remain button Cassette Compartment Rear Panel Removal Word on the Exclusive 3N-100AAS Battery PackSpecification of Battery Installation VCR Display REW button Press to start play backFF button Connection with a Video Camera Connections Output Typical Connection with the Sequential SwitcherVideo To REC TRIGG. OUT Contents of Screen Display Alarm Recall Screen Operation Setting the Clock Monitor screen ON-SCREEN FunctionsDate-Time Display VCR display Display Screen This function enables to indicate and record information Alarm numberIs pressed. When an alarm is Changes to the alarm number Counter Memory Alarm MemoryWhen the tape reaches Counter Displays Code Number Condition of Abnormality Error MessageRegarding the error code E-6 Display Tape Remain Setting the RECORDING/PLAY Back Time HOW to Operate 24 Hour Virtual Real Time ModeMode display Loading and Unloading a Video Cassette Loading a CassetteUnloading a Cassette Camera and monitor TV Not been removed Recording Restart Recording Setting the Restart Recording Program Screen Timer RecordingSetting the Timer Program Daily Timer Recording During timer power off mode, alarm recording will not Time Mode button is pressed, the displayPress the Timer button Should be more than 1 minute. If they are same, timer Weekly Timer Recording Press the Shift ButtonGRAM.to blink PROPress the Shift Button to blink the MO1 start time DLY Overlapping ProgramsExample FR2 Event Recording Alarm RecordingOperation at Alarm Input Alarm Recall Display Connecting the Alarm Terminals Manual Setting the Alarm RecordingDisplay Recording time Cont Auto recording Connecting the External control terminalAuto Recording Operation of Auto Recording Press the + or SET How to Release Auto RecordingHow to Forbid Auto Recording Press Timer button to release the timer mode Display Operation after detection of tape end How to Set to Stop at End of TapeSetting contents Buzzer Screen display Counter display Operation After Tape END Detection How to Set to Auto Rewind at End of Tape Alarm recording does not operate during auto-rewindMenu Screen ButtonREC. to select REW → How to Set to Repeat Record at End of Tape C D a B C D Recording with the Sequential SwitcherConnection with the Sequential Switcher Timing for Camera Switching Trigger SEL REC Trigger Output Selection in the Alarm RecordingPress the Shift Button to set the REC Tracking Adjustment Recording time mode Time mode for playbackPlayback Slow Still Play Using the Shuttle DialREW Stop Picture Search Play Playback in Various Modes Time Date Search Search OperationPress the SET button to Set the Minute to Alarm Search Alarm M to lightStill picture mode Press the Play button Input/Output terminal Signal level Additional remarks Signal Levels of INPUT/OUTPUT Terminals Order of Daily Checks Check the playback picture recorded in SPA2 modePress the or Time Mode button to go to SPA2 mode Daily and Periodic Inspection Steps to Take after Daily Checks Request for Periodic ChecksTape Usage Frequency Dew Condensation Recording Before Calling Service PersonnelInstallation Function/Operation Other matters Playback Dew caution sheet SpecificationsConnector section Accessories 70971826 Limited Warranty