TIME DATE SEARCH

Searching a picture at a desired day and time is possible by specifying the day and hour on the MENU screen.

The VCR automatically records the current date and time (day/hour/minute). Accordingly, make sure before recording that the date and time is exactly adjusted.

Search Operation

In case of searching the picture at day of 28, 17:30 minutes in reverse direction;

INTRODUCTION

Press the DISPLAY

1 button.

DISPLAY TIME MODE +

SET

TRACKING

M E N U

CLOCK ADJUST SETUP DISPLAY MODE PROGRAM

Press the SET button to

4 set the HOUR to 17 and press the SHIFT button.

DISPLAY TIME MODE +

TIME DATE SEARCH

DAY

28

HOUR

17

MINUTE

00

PREPARATION

SHIFT

LOCATION SELECT

ALARM RECALL TIME DATE SEARCH

SET

SHIFT

TRACKING

FORWARD

REVERSE

END=[DISPLAY]

LOCATION SELECT

MENU=[DISPLAY]

Press the SHIFT button

2 to blink TIME DATE SEARCH and press the SET button.

DISPLAY TIME MODE +

TIME DATE SEARCH

DAY

01

HOUR

00

MINUTE

00

Press the SET button to

5 set the MINUTE to 30.

DISPLAY TIME MODE +

TIME DATE SEARCH

DAY

28

HOUR

17

MINUTE

30

SET

SHIFT

TRACKING

SEARCH

FORWARD

 

REVERSE

SHIFT

TRACKING

 

 

LOCATION SELECT

FORWARD

REVERSE

LOCATION SELECT

MENU=[DISPLAY]

MENU=[DISPLAY]

Press the SET button to

3 set the DAY to 28 and press the SHIFT button.

DISPLAY TIME MODE +

TIME DATE SEARCH

DAY

28

HOUR

0

MINUTE

00

Press the SHIFT button

6 to blink the REVERSE, and press the SET button.

DISPLAY TIME MODE +

TIME DATE SEARCH

DAY

28

HOUR

17

MINUTE

30

SET

SHIFT

TRACKING

FORWARD

REVERSE

SET

SHIFT

TRACKING

FORWARD

REVERSE

LOCATION SELECT

MENU=[DISPLAY]

LOCATION SELECT

MENU=[DISPLAY]

Notes:

iTime date search is not carried out if the time adjustment has been not completed.

iTime date search is not carried out for tapes recorded by a unit which can’t automatically record data of time and date.

iTime date search will not operate when searching a section of tape that has an alarm on it. In this case perform alarm search.

iTime date search may cause a time error listed in the following to the specified time.

iTime date search may not be carried out in the areas at REC start and REC end shown below.

 

 

 

 

 

 

 

 

 

 

A (Not carry out in

Time error to the

 

 

 

 

 

 

 

 

 

Record mode

the REC end area

specified time at

 

 

 

 

 

 

 

 

 

 

at maximum)

maximum

 

 

 

 

 

 

 

 

 

SPA2, EPA6, SPA12,

 

 

 

 

 

 

 

 

 

 

 

EPA18, SPA24, SP24, EP30,

1 min.

1 min.

 

 

 

 

 

 

 

 

 

EP48, EP72, EP120

 

 

REC start

REC end

SP48, SP72, EP168, EP240

3 min.

3 min.

 

 

 

 

 

 

 

 

 

less than

 

 

 

 

 

 

 

less than A

SP120

4 min.

4 min.

 

 

 

 

 

 

 

 

 

 

 

 

 

SP168, EP480

5 min.

5 min.

1min.

 

 

 

 

 

 

 

 

 

 

 

SP240, EP720

7 min.

7 min.

 

 

 

 

 

 

 

 

 

EP960

9 min.

9 min.

 

 

 

 

 

 

 

 

 

SP480

12 min.

12 min.

 

 

 

 

 

 

 

 

 

SP720

18 min.

18 min.

 

 

 

 

 

 

 

 

 

SP960

23 min.

23 min.

PLAYBACK

OPERATION

NOTICE

42

Page 43
Image 43
Toshiba kV-9960A instruction manual Time Date Search, Search Operation, Press the SET button to Set the Minute to