Toshiba TDP-P75 Shutdown

Operation 29

English

Shutdown

1. Press ON/STANDY and a

confirmation prompt displays. Press

ON/STANDY a second time to turn

the projector off.

2. The ON indicator flashes orange

and the lamp shuts down. The fans

will continue to run for approximately

90 seconds to cool down the

projector lamp.

• To protect the lamp, the projector will not

respond to any commands during the

cooling process.

• Do not unplug the power cord before the

projector shutdown sequence is

complete or during the 90-second cooling down process.

Note

• Note that a lamp characteristics may rarely cause the brightness to fluctuate

slightly.

• A lamp is consumable item. If used for extended periods, images will appear

dark, and the lamp could burn out. This is characteristic of a lamp, and is not

malfunction. (The lifetime of the lamp depends on conditions of use.)

• The DMDTM is made using extremely advanced technology, but there may be

black spots (pixels that do not light) or bright spots (pixels that are constantly lit)

on the panel. Please note that these are not malfunctions.

CAUTION

• Do not block the projection lens from projecting as this could cause the blocking

object to become heated and deformed.

• Do not look into the lens while the lamp is on. The strong light from the lamp may

cause damage to your eyes or sight.

• Do not block the air intake or exhaust. Doing so may cause damage to the

projector due to internal overheating.

• Do not place your hands, face, or other objects near the air exhaust. Doing so may

cause burns, deform/break the object.

Press the [ON/STANDBY] button again to turn off.

Contents

Main SAFETY PRECAUTION MODEL NAME: TDP-P75 Page IMPORTANT SAFETY INSTRUCTIONS 1. Read owner's manual 2. Power sources 3. Source of light 4. Heat 5. Ventilation 6. Water and moisture 7. Cleaning 8. Power cord protection 9. Overloading 11. Lightning storms 12. Do not place the product vertically. 13. Attachments 14. Do not stack components. 15. Accessories 16. Damage requiring service 18. Servicing 19. Replacement parts 20. Safety check POWER SUPPLY CORD SELECTION 22. Do not use the product in a closed installation state. IMPORTANT PRECAUTIONS Save Original Packing Materials Moisture Condensation Location and Installation Avoid Volatile Liquids EXEMPTION CLAUSES OTHER NOTES AND INFORMATION Copyrights Disposal WEEE Directive Trademarks REMOTE CONTROL BATTERIES Caution Note Contents Page Overview Shipping contents Projector exterior view Front / Upper side Bottom side Rear side Controls and functions Control panel Remote control Name : Main Function Remote Control Front Rear Preparing and using the remote control Dry-cell batteries The remote control the remote control Preparing and using the remote control (Continued) Operating a computer using the remote control Connecting a computer Operating a computer 1 2 Positioning your projector Choosing a location WARNING Projection distance and size Connection e a (min length) = a (max length) = As seen from the sid Connecting to a computer Connecting to a Component Video device Overview 25 Connecting Video and S-Video devices Operation Start up Adjusting the image Adjusting the height Fine-tuning the image size and clarity Auto-adjusting the image Adjusting the volume Switching input signals Shutdown Menu operation Menu system Functions available when receiving different signal types... Using the menus 1. Image adjustment menu 2. Display setting menu 3. Default setting menu 4. Information menu Additional Information Care of the projector Cleaning the lens Cleaning the projector case WARNIN G About the lamp Lamp warning message Replacing the lamp WARNING CAUTION Page Indicator lights When the projector is in an abnormal state: When the projector is in a normal state: POWER TEMP LAMP State Remark Troubleshooting 41 Troubleshooting Problem Cause Remedy No picture. The projector does not turn on. Image is unstable. Specifications Projector specifications Dimensions Signal timing Supported signal format for Component-YPBPR Input 238 180 86.8 Supported signals for Video and S-Video inputs Regulation statements FCC statement EEC statement MIC statement B class equipment (Household purpose info/telecommunications equipment)