Set for use as analog RGB input | Toshiba TLP560, TLP260, TLP261

Connecting video equipment (continued)

CONTENTS

You can project the picture from video equipment with component video output jack.

Check that the power supplies for the projector and for the video equipment are off before connecting the cables.

				COMPUTER IN connector
				For use as both analog RGB and Y/PB/PR input. At shipping from factory, it is
		COMPUTER OUT	COMPUTER IN	set for use as analog RGB input.
CONTROL USB AUDIO IN	VIDEO IN S-VIDEO IN	(Y/PB/PR )	( Y/PB/PR )	Change the setting on the menu screen when using as Y/PB/PR input. 45

AUDIO IN jack

For use as audio signal of all input sources.

Video equipment (DVD player, etc.)

25

connectionsInstallation and

To COMPUTER IN connector

Be sure to connect in the proper direction.

Monitor cable

Mini D-sub 15P-BNC (Not supplied)

To AUDIO IN jack

Audio cable (supplied)

Adapter
BNC-pin
(Not supplied)	(Green) To Y video output
	(Blue) To PB video output
	(Red) To PR video output
	Pin plug (red)
	To audio output (R)
	Pin plug (white)
	To audio output (L)

Image 25

Toshiba TLP560, TLP260, TLP261, TLP561 owner manual Set for use as analog RGB input

Contents

TLP560/TLP260 TLP260 Safety Precautions Avoid Volatile Liquid Save Original Packing MaterialsMoisture Condensation Exemption Clauses Source of Light Power SourcesVentilation Important Safety Instructions Object and Liquid Entry AccessoriesDo not place the product vertically Stack Inhibited Replacement Parts Damage Requiring ServiceSafety Check Servicing Heat could erase or discolor the letters on a thermal paper Do not carry by the camera armDo not move the projector while the arm is still erect Do not look into the arm light while it is lit Before Power supply cord selection Contents SpeakerLens Carrying handle Names of each part on the main unitAnti-theft lock hole ON/STANDBY button Names of each part on the main unit Control connector 26 72 RS-232C connector USB connectorVideo in connector Computer OUT connector Freeze button Names of each part on the remote control Loading batteries Install the batteriesOpen the cover Attach the cover Front side Rear side Remote control operation Floor-mounted projector placement Side view Determine the screen size projected on the screen Take off the lens cover Connect the power cordInsert the other end into a wall outlet Lens shift function Turn clockwise to lift up Turn counterclockwise to lower Turn the foot adjuster to make fine adjustment to the height Ceiling-mounted projector placement Connecting a computer Audio in jack Connecting video equipment Set for use as analog RGB input Projector operation control by a computer How to use the output connector Lamp indicator blinks while the lamp is warming up Remote controlProjection on the screen Press ON/STANDBY Press Enter to confirm Turn on the connected equipment and put it in playback modeControl panel Main unit side Language Press Input and hold for two seconds Select the input source by pressing Input repeatedlyPress Enter Input source selection menu appears Focusing ring Adjust the picture size by turningZooming lever Focus on the picture by turning Press the + button to increase volume Press VOL/ADJ +/- to adjust volumePress the button to decrease volume Press ON/STANDBY after using the projector Turning the power offPress ON/STANDBY again Input full screen video signals from the input Adjusting the picture automaticallySource computer and project the image Press Auto SET To finish the adjustment, press Exit repeatedly Adjust the distortion with the selection buttonsCorrecting the keystone distortion Press Keystone Cutting off the picture and sound temporarily Icon appears in the mute modePress Mute Sound and picture are cut off temporarily Freezing the picture Icon appears in the freeze modePress Freeze Picture freezes Enlarging the picture size Icon appears in the resize modePress Resize To reduce the enlargement ratio, press the Resize button Press PIP Displaying PIP Sub-picturesSub-picture is displayed Press Call Displaying Information Start a presentation on the computer Operating the presentation mode Select the computer input with Input Adjust the projector before presentation if necessaryPress P.MODE and hold for two seconds Change a slide with the selection buttons Press Menu Operating the menu screen Start Adjust with VOL/ADJ +/- or selection buttons Adjust the image flicker Guide Menu adjustments and settings Reset Full Menu adjustments and settings Picture Full Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Menu background is normal Reset Full Menu adjustments and settings Display Full Menu settings Default setting Full Menu settings Reset PIP menu setting ImagingDocument camera Part names of the document imaging camera model Preparation of the document imaging camera Set a document to be projected Press ARM LightCamera control panel Light turns on Picture projection with the document imaging camera Press Camera to select the camera input mode Press Camera Gain +/- to improve view of a When finished, turn off the light and close itCamera subject which is too dark or vivid Put back the arm Project a white paper and enlarge it to fill Locking the white balanceScreen With the document camera operating, fully Correcting illuminated defectsCover the camera lens with a piece of black Paper or cloth Trouble indications IndicatorsControl panel Main unit side Unplug the power cord Take off the front cover Air filter cleaningClean the air filter Detach the air filter Mount the front cover Mount the air filter and the filter frameLens side to fix it Cleaning the lens Lens and main unit cleaningCleaning the main unit Replacing the intake, exhaust fans and air filter Unplug the power cord Wait until the lamp gets cool enough Lamp replacementTake off the lamp cover on the bottom panel Pull out the lamp Load a new lamp Reset the lamp timerAttach the lamp cover Slide the cover into place and tighten the two screws Symptom Cause Correction Before calling service personal Before calling service personal Pin assignment of Computer IN, Computer OUT connector Applicable computer signal Applicable signal Compatible Video and S-Video signal Applicable signal Signal assignment of RS-232C Interface format Controlling the projector by using RS-232C Controlling the projector by using RS-232C VLU Computer Resize Main unit Specifications Replacement lamp Specifications