Turning the power off, Press ON/STANDBY again | Toshiba TLP560

Turning the power off

CONTENTS

33

Remote control

ON /

STANDBY

INPUT			1,2
KEYSTONE		AUTO SET	1,2
FREEZE	MUTE
PIP	CALL	RESIZE

1

2

ON/STANDBY

ON/STANDBY

ON/STANDBY

ON/STANDBY

Press ON/STANDBY after using the projector.

An instruction message for turning the power off appears on the screen and disappears after a while. When the message disappears, operation becomes invalid.

Press ON/STANDBY again.

Cooling starts. Once cooling is completed, the LAMP and FAN indicators turn off and the standby mode is set. (The ON indicator turns in orange.)

	MENU
	VOL / ADJ
ENTER	EXIT /
	P.MODE

	ON	LAMP
	ON	(Green)
		(Green)
	(Orange) Flashing
		FAN

A (Green)

LAMP

ON

(Off) (Orange)

B

FAN

(Green)

LAMP

ON

(Off) (Orange)

C

FAN

(Off)

Operations

CT-90106

Control panel (Main unit side)

1,2									2
1,2							ON / STANDBY		Indicators
						P	T
				ON		LAM	EMP	FAN
				ON				FAN
				TE				EXI
				EN	R			T
				U				A
				U				UT
				N				O	S
				E					S
				M					ET
									K
				T					E
				T					S
			U						Y
	N	P	U						T
I		P							O
									N
									E

VOL / ADJ

ATo protect the light source lamp, the LAMP indicator blinks as long as a minimum of cooling is necessary. The power cannot be turned back on during this time. Unplugging the power cord at this time will shorten the lamp’s duration life.

BThe cooling fan continues to run for a while to expel the heat remaining inside. If you are in a hurry, however, you may unplug the power cord at this time.

CThe standby mode is set.

Notes

•The projector consumes about 15W of power in the standby mode. We recommend you unplug the power cord when not using the projector for long periods of time.

•Be sure that the LAMP indicator has turned off before unplugging the power cord. Cutting the power by unplugging the power cord while the projector is operating or the light source lamp is being cooled will shorten the lamp’s duration life. Should a fault or some other irregularity arise with this unit, unplug the power cord.

•When reinserting the power plug before the lamp has cooled, please wait until the lamp has cooled sufficiently before use. When the lamp is at a high temperature, it may not light and it’s life duration will be shortened.

Image 33

Toshiba TLP560, TLP260, TLP261 Turning the power off, Press ON/STANDBY after using the projector, Press ON/STANDBY again

Contents

TLP560/TLP260 TLP260 Safety Precautions Avoid Volatile Liquid Save Original Packing MaterialsMoisture Condensation Exemption Clauses Power Sources Source of LightVentilation Important Safety Instructions Object and Liquid Entry AccessoriesDo not place the product vertically Stack Inhibited Replacement Parts Damage Requiring ServiceSafety Check Servicing Heat could erase or discolor the letters on a thermal paper Do not carry by the camera armDo not move the projector while the arm is still erect Do not look into the arm light while it is lit Before Power supply cord selection Contents Names of each part on the main unit SpeakerLens Carrying handleAnti-theft lock hole ON/STANDBY button Names of each part on the main unit Control connector 26 72 RS-232C connector USB connectorVideo in connector Computer OUT connector Freeze button Names of each part on the remote control Loading batteries Install the batteriesOpen the cover Attach the cover Front side Rear side Remote control operation Floor-mounted projector placement Side view Determine the screen size projected on the screen Connect the power cord Take off the lens coverInsert the other end into a wall outlet Lens shift function Turn clockwise to lift up Turn counterclockwise to lower Turn the foot adjuster to make fine adjustment to the height Ceiling-mounted projector placement Connecting a computer Audio in jack Connecting video equipment Set for use as analog RGB input Projector operation control by a computer How to use the output connector Lamp indicator blinks while the lamp is warming up Remote controlProjection on the screen Press ON/STANDBY Press Enter to confirm Turn on the connected equipment and put it in playback modeControl panel Main unit side Language Press Input and hold for two seconds Select the input source by pressing Input repeatedlyPress Enter Input source selection menu appears Focusing ring Adjust the picture size by turningZooming lever Focus on the picture by turning Press VOL/ADJ +/- to adjust volume Press the + button to increase volumePress the button to decrease volume Turning the power off Press ON/STANDBY after using the projectorPress ON/STANDBY again Input full screen video signals from the input Adjusting the picture automaticallySource computer and project the image Press Auto SET To finish the adjustment, press Exit repeatedly Adjust the distortion with the selection buttonsCorrecting the keystone distortion Press Keystone Cutting off the picture and sound temporarily Icon appears in the mute modePress Mute Sound and picture are cut off temporarily Freezing the picture Icon appears in the freeze modePress Freeze Picture freezes Enlarging the picture size Icon appears in the resize modePress Resize To reduce the enlargement ratio, press the Resize button Displaying PIP Sub-pictures Press PIPSub-picture is displayed Press Call Displaying Information Start a presentation on the computer Operating the presentation mode Select the computer input with Input Adjust the projector before presentation if necessaryPress P.MODE and hold for two seconds Change a slide with the selection buttons Press Menu Operating the menu screen Start Adjust with VOL/ADJ +/- or selection buttons Adjust the image flicker Guide Menu adjustments and settings Reset Full Menu adjustments and settings Picture Full Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Menu background is normal Reset Full Menu adjustments and settings Display Full Menu settings Default setting Full Menu settings Reset PIP menu setting ImagingDocument camera Part names of the document imaging camera model Preparation of the document imaging camera Set a document to be projected Press ARM LightCamera control panel Light turns on Picture projection with the document imaging camera Press Camera to select the camera input mode Press Camera Gain +/- to improve view of a When finished, turn off the light and close itCamera subject which is too dark or vivid Put back the arm Locking the white balance Project a white paper and enlarge it to fillScreen With the document camera operating, fully Correcting illuminated defectsCover the camera lens with a piece of black Paper or cloth Trouble indications IndicatorsControl panel Main unit side Unplug the power cord Take off the front cover Air filter cleaningClean the air filter Detach the air filter Mount the air filter and the filter frame Mount the front coverLens side to fix it Cleaning the lens Lens and main unit cleaningCleaning the main unit Replacing the intake, exhaust fans and air filter Unplug the power cord Wait until the lamp gets cool enough Lamp replacementTake off the lamp cover on the bottom panel Pull out the lamp Load a new lamp Reset the lamp timerAttach the lamp cover Slide the cover into place and tighten the two screws Symptom Cause Correction Before calling service personal Before calling service personal Pin assignment of Computer IN, Computer OUT connector Applicable computer signal Applicable signal Compatible Video and S-Video signal Applicable signal Signal assignment of RS-232C Interface format Controlling the projector by using RS-232C Controlling the projector by using RS-232C VLU Computer Resize Main unit Specifications Replacement lamp Specifications