Connecting video equipment, Audio in jack | Toshiba TLP260, TLP560

Connecting video equipment

CONTENTS

You can project the picture from video equipment.

Check that the power supplies for the projector and for the video equipment are off before connecting the cables.

24

				VIDEO IN jack
	VIDEO IN S-VIDEO IN	COMPUTER OUT	COMPUTER IN	S-VIDEO IN connector
CONTROL USB AUDIO IN	VIDEO IN S-VIDEO IN	( Y/PB/PR )	( Y/PB/PR )

				AUDIO IN jack
				For use as audio signal of all input sources.

To S-VIDEO IN connectorTo S-video output Be sure to connect in the proper

direction.

S-video cable (not supplied)

To AUDIO IN jack (Yellow) To VIDEO IN jack Video cable	Audio cable
(supplied)	(supplied)

Video equipment

Pin plug (red)

To audio output (R)

Pin plug (white)

To audio output (L)

Pin plug (yellow)

To video output

connectionsInstallation and

Note

The S-VIDEO IN connector and VIDEO IN jack can be used independently, but the audio input jack is used for all input sources.

Continued

Image 24

Toshiba TLP260, TLP560, TLP261, TLP561 owner manual Connecting video equipment, Audio in jack

Contents

TLP260 TLP560/TLP260 Safety Precautions Save Original Packing Materials Avoid Volatile LiquidMoisture Condensation Exemption Clauses Power Sources Source of LightVentilation Important Safety Instructions Accessories Object and Liquid EntryDo not place the product vertically Stack Inhibited Damage Requiring Service Replacement PartsSafety Check Servicing Do not carry by the camera arm Heat could erase or discolor the letters on a thermal paperDo not move the projector while the arm is still erect Do not look into the arm light while it is lit Power supply cord selection Before Contents Names of each part on the main unit SpeakerLens Carrying handleAnti-theft lock hole Names of each part on the main unit ON/STANDBY button USB connector Control connector 26 72 RS-232C connectorVideo in connector Computer OUT connector Names of each part on the remote control Freeze button Install the batteries Loading batteriesOpen the cover Attach the cover Remote control operation Front side Rear side Floor-mounted projector placement Determine the screen size projected on the screen Side view Connect the power cord Take off the lens coverInsert the other end into a wall outlet Lens shift function Turn the foot adjuster to make fine adjustment to the height Turn clockwise to lift up Turn counterclockwise to lower Ceiling-mounted projector placement Connecting a computer Connecting video equipment Audio in jack Set for use as analog RGB input Projector operation control by a computer How to use the output connector Remote control Lamp indicator blinks while the lamp is warming upProjection on the screen Press ON/STANDBY Turn on the connected equipment and put it in playback mode Press Enter to confirmControl panel Main unit side Language Select the input source by pressing Input repeatedly Press Input and hold for two secondsPress Enter Input source selection menu appears Adjust the picture size by turning Focusing ringZooming lever Focus on the picture by turning Press VOL/ADJ +/- to adjust volume Press the + button to increase volumePress the button to decrease volume Turning the power off Press ON/STANDBY after using the projectorPress ON/STANDBY again Adjusting the picture automatically Input full screen video signals from the inputSource computer and project the image Press Auto SET Adjust the distortion with the selection buttons To finish the adjustment, press Exit repeatedlyCorrecting the keystone distortion Press Keystone Icon appears in the mute mode Cutting off the picture and sound temporarilyPress Mute Sound and picture are cut off temporarily Icon appears in the freeze mode Freezing the picturePress Freeze Picture freezes Icon appears in the resize mode Enlarging the picture sizePress Resize To reduce the enlargement ratio, press the Resize button Displaying PIP Sub-pictures Press PIPSub-picture is displayed Displaying Information Press Call Operating the presentation mode Start a presentation on the computer Adjust the projector before presentation if necessary Select the computer input with InputPress P.MODE and hold for two seconds Change a slide with the selection buttons Operating the menu screen Press Menu Adjust with VOL/ADJ +/- or selection buttons Start Guide Menu adjustments and settings Adjust the image flicker Full Menu adjustments and settings Picture Reset Full Menu adjustments Position Full Menu adjustments Color Full Menu adjustments and settings Audio Full Menu adjustments and settings Display Menu background is normal Reset Full Menu settings Default setting Full Menu settings Reset PIP menu setting Part names of the document imaging camera model ImagingDocument camera Preparation of the document imaging camera Press ARM Light Set a document to be projectedCamera control panel Light turns on Press Camera to select the camera input mode Picture projection with the document imaging camera When finished, turn off the light and close it Press Camera Gain +/- to improve view of aCamera subject which is too dark or vivid Put back the arm Locking the white balance Project a white paper and enlarge it to fillScreen Correcting illuminated defects With the document camera operating, fullyCover the camera lens with a piece of black Paper or cloth Indicators Trouble indicationsControl panel Main unit side Air filter cleaning Unplug the power cord Take off the front coverClean the air filter Detach the air filter Mount the air filter and the filter frame Mount the front coverLens side to fix it Lens and main unit cleaning Cleaning the lensCleaning the main unit Replacing the intake, exhaust fans and air filter Lamp replacement Unplug the power cord Wait until the lamp gets cool enoughTake off the lamp cover on the bottom panel Pull out the lamp Reset the lamp timer Load a new lampAttach the lamp cover Slide the cover into place and tighten the two screws Before calling service personal Symptom Cause Correction Before calling service personal Pin assignment of Computer IN, Computer OUT connector Applicable signal Applicable computer signal Applicable signal Compatible Video and S-Video signal Controlling the projector by using RS-232C Signal assignment of RS-232C Interface format Controlling the projector by using RS-232C VLU Computer Resize Specifications Main unit Specifications Replacement lamp