Toshiba TLP780U & Adjustments

FULL MENU adjustments - Color

48

You can adjust the color condition of the picture from FULL MENU [Color].

The relationship between input source and item

Yes: Adjustable

-: Not displayed

To operate FULL MENU, refer to page 44 .

Analog RGB(1)

Analog RGB(2)

Digital RGB

Y/PB/PR

Video

S-Video

Camera

Color

ADJ.

Adjusting color deepness of the picture

-

-

-

Yes

Yes

Yes

-

Tint

ADJ.

Adjusting tint of the picture (not adjustable at PAL, SECAM, PAL-N,PAL-M and PAL60)-

-

-

-

Yes

Yes

-

R-level

ADJ.

Adjusting red's color level of the picture

Yes

Yes

Yes

Yes

Yes

Yes

Yes

G-level

ADJ.

Adjusting green's color level of the picture

Yes

Yes

Yes

Yes

Yes

Yes

Yes

B-level

ADJ.

Adjusting blue's color level of the picture

Yes

Yes

Yes

Yes

Yes

Yes

Yes

Reset

EXEC.

The adjustments of FULL MENU [Color] are returned to the factory default value

Yes

Yes

Yes

Yes

Yes

Yes

Yes

& Adjustments

Settings

Notes

•The adjustments made are memorized automatically when the power is turned off by pressing the ON/STANDBY button. If the power cord is unplugged or if a power failure occurs while the projector is on, the adjustments are not memorized.

Contents

Page Note: WARNING: Notice: CAUTION: use Before Save Original Packing Materials Avoid Volatile Liquid Moisture Condensation Page 5.Heat 6.Water and Moisture 7.Cleaning 8.Power-CordProtection 9.Overloading 11.Object and Liquid Entry 12.Do not place the product vertically 13.Stack Inhibited 14.Attachments 15.Accessories 16.Damage Requiring Service 18.Servicing 19.Replacement Parts 20.Safety Check 22.Do not carry by the camera arm 24.Do not move the projector while the arm is still erect 25.Do not look into the arm light while it is lit If your line voltage is 220 to 240V, use one of the following types of cable Connecting a computer (COMPUTER IN 1 connector) Connecting a computer (COMPUTER IN 2 connector) GUIDE MENU adjustments and settings FULL MENU adjustments and settings - Picture FULL MENU adjustments and settings - Audio Front side Top side Page Caution Location of the labels R-CLICK button L-CLICK button FREEZE button (Bottom Side) Open the cover Install the batteries Attach the cover Rear side Floor-mountedfront projection Floor-mountedrear projection Place the projector on a steady, level surface such as a table Determine the screen size projected on the screen Connect the power cord 4 Take off the lens cover Turn the foot adjuster to make fine adjustment of the height CAUTION and Installation connection Page Page Page Page Page CAUTION Remote control Press ON/STANDBY Operations Select a desired language with the selection button ( / ), and press ENTER Press ENTER to decide Control panel (Main unit side) Select the input source by pressing INPUT repeatedly INPUT Press INPUT and hold for two seconds Select the input source to project with the selection button ( / ) Press ENTER Adjust the picture size by turning the zooming lever Focus on the picture by turning the focusing ring Press VOL/ADJ (+/-)to adjust volume KEYSTONE Press ON/STANDBY after using the projector Press ON/STANDBY again Control panel AUTO SET Input full screen video signals from the input source (computer) and project the image Press AUTO SET AUTO SET Press KEYSTONE Confirm the keystone distortion Press EXIT repeatedly until the menu disappears Press MUTE MUTE Press FREEZE FREEZE Press RESIZE () FREEZE Press PIP PIP Press CALL CALL R-CLICK L-CLICK L-CLICK R-CLICK Start Press MENU FULL MENU MENU Press MENU button once again Select the item with the selection button (/) Select the item with selection buttons (/) Adjust with VOL/ADJ (+/-) Press ENTER Select it with the button indicated on the button operation guide End & Adjustments Settings Page Settings & Adjustments Page Page Page & Adjustments Page LOCK (W.BALANCE) indicator W.BALANCE button OVERLAY button ARM LIGHT button CAMERA button Page Camera control panel Press ARM LIGHT Set a document to be projected Document camera imaging Press CAMERA to select the camera input mode Move the camera head to adjust the size of the picture Focus on the picture by turning the focusing ring on the camera head Press CAMERA GAIN (+/-)to improve view of a camera subject which is too dark or vivid When finished, turn off the light and close it and put back the arm Set the white paper on a flat place and set the camera so that paper is projected to the full screen Select the input source using the overlay function by pressing INPUT Press OVERLAY Project a white paper and enlarge it to fill the screen W.BALANCE Press W.BALANCE to turn the LOCK indicator on W.BALANCE With the document camera operating, fully cover the camera lens with a piece of black paper or cloth Document camera imaging ARM LIGHT The power does not come on Unplug the power cord Take off the air filter cover Detach the air filter Clean the air filter Maintenance Assemble the air filter Mount the air filter cover Cleaning the lens Cleaning the main unit Replacing the intake, exhaust fans and air filter 2 Wait until the lamp gets cold enough Take off the lamp cover on the bottom panel Pull out the lamp Load a new lamp Attach the lamp cover Reset the lamp timer Maintenance Page Page Page Applicable computer signal The compatible Video and S-Videosignal The compatible components video signal (Y/PB/PR) Signal assignment of RS-232C Interface format Command list ARG ALF Page Page Page Page Page Main unit Liquid crystal display Projection lens Document imaging camera (with camera model) Accessories Sold separately