Daisy-Chaining- If the CD-ROM you are installing is one of two or more SCSI devices you have connected to your system, you will need to use a custom built SCSI interface cable. Remember that the termi- nator jumper on the CD-ROM drive must have the jumper installed when the drive is the last device in the chain.

T

X

M

6

4

0

1

F

1

X

M

6

4

0

1

B

Host Computer

 

 

 

 

 

 

 

 

I/F Card

SCSI Cable

 

Interface

 

 

 

 

 

 

 

 

Connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

CD-ROM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DRIVE

 

Terminator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

External Terminator

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(see notes 1 & 3)

Host Computer

 

 

 

 

Interface

 

 

 

 

 

 

 

 

 

 

 

I/F Card

SCSI Cable

 

 

 

Connector

 

 

 

 

 

 

 

 

 

 

 

 

 

CD-ROM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DRIVE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Terminator

 

 

 

 

 

 

(see note 1)

 

 

 

 

 

 

 

 

TXM6401F1/XM-6401B CONNECTION (ONE DRIVE)

Host Computer

SCSI Cable

 

 

 

 

 

 

I/F Card

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Terminator

If connecting more than three SCSI devices, you need to use a custom built SCSI Interface Cable.

XM-6401B

INTERNAL DRIVE(S) Interface Connector

CD-ROM

DRIVE #1

(see note 2)

CD-ROM

DRIVE

#2

(see note 2)

CD-ROM

DRIVE

#N

(N < 7)

TXM6401F1

EXTERNAL DRIVE(S)

SCSI Interface Connector from

host computer

CD-ROM

DRIVE

#1

(see note 2)

CD-ROM

DRIVE

#2

(see note 2)

CD-ROM

DRIVE

#N

(N < 7)

Install Terminator Jumper

Install External

only on the last drive of BUS

Terminator on last drive on BUS

(see note 1)

(see notes 1 & 3)

TXM6401F1/XM-6401B DAISY-CHAIN CONNECTION (MULTIPLE DRIVES)

Notes:

1.Terminator jumper must be jumpered when CD-ROM is the last or only device on the SCSI BUS.

2.Terminator jumper should be removed when CD is in a "daisy-chain" and is NOT the last drive.

3.The TXM6401F1 uses an external terminator which must be attached to the last drive of a "daisy chain". The external terminator is an optional item.

10TOSHIBA XM-6401B/TXM6401F1 CD-ROM Drive

Page 15
Image 15
Toshiba (T)XM6401B/F1 instruction manual TXM6401F1/XM-6401B Connection ONE Drive