TL-R402M Cable/DSL Router User Guide | TP-Link instruction

Figure 5-4 WAN - Dynamic IP

TL-R402MCable/DSL Router User Guide

Figure 5-4 WAN - Dynamic IP

This page displays the WAN IP parameters assigned dynamically by your ISP, including IP address, Subnet Mask, Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters.

¾MTU Size: The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. For some ISPs you need to reduce the MTU. But this is rarely required, and should not be done unless you are sure it is necessary for your ISP connection

¾If your ISP gives you one or two DNS addresses, select Use These DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from ISP

¾Get IP with Unicast DHCP: A few ISPs' DHCP servers do not support the broadcast applications. If you cannot get the IP address normally, you can choose this option. (You generally need not check this option)

Note:

If you get Address not found errors when you go to a Web site, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses.

2.If you choose Static IP, you should have fixed IP parameters specified by your ISP. The Static IP settings page will appear, shown in Figure 5-5:

16

Image 21

TP-Link manual TL-R402M Cable/DSL Router User Guide, 4WAN - Dynamic IP

Contents

Page COPYRIGHT & TRADEMARKS SAFETY NOTICES FCC STATEMENTEC DECLARATION OF CONFORMITY EUROPE COMMENT Appendix A TL-R402M Cable/DSL Router User Guide Package contents 1.1 Purposes Chapter 1. About this Guide1.2 Conventions 1.3 Overview of this User Guide Chapter 2. Introduction 2.2 Features2.1 Overview of the Router TL-R402M Cable/DSL Router User Guide TL-R402M Cable/DSL Router User Guide 2.3 Panel LayoutName Action Figure 2-2Rear Panel sketch TL-R402M Cable/DSL Router User Guide 3.2 Installation Environment Requirements Chapter 3. Connecting the Router3.3 Connecting the Router 3.1 System Requirements TL-R402M Cable/DSL Router User Guide Chapter 4. Quick Installation Guide 4.1 TCP/IP configurationTL-R402M Cable/DSL Router User Guide TL-R402M Cable/DSL Router User Guide 4.2 Quick Installation Guide TL-R402M Cable/DSL Router User Guide Figure 4-4Login Windows Figure 4-6Choose WAN Connection Type TL-R402M Cable/DSL Router User Guide TL-R402M Cable/DSL Router User Guide Figure 4-9Quick Setup - Finish 5.1 Login Chapter 5. Configuring the Router5.2 Status TL-R402M Cable/DSL Router User Guide 5.4Network 5.3 Quick Setup5.4.1 LAN TL-R402M Cable/DSL Router User Guide TL-R402M Cable/DSL Router User Guide 5.4.2 WAN Figure 5-4WAN - Dynamic IP TL-R402M Cable/DSL Router User Guide Figure 5-5WAN - Static IP TL-R402M Cable/DSL Router User Guide TL-R402M Cable/DSL Router User Guide ¾Connect on Demand - You can configure the router to disconnect your Internet connection after a specified period of inactivity Max Idle Time. If your Internet connection has been terminated due to inactivity, Connect on Demand enables the router to automatically re-establishyour connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, click the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates TL-R402M Cable/DSL Router User Guide Figure 5-7PPPoE Advanced Settings Figure 5-8WAN - L2TP TL-R402M Cable/DSL Router User Guide TL-R402M Cable/DSL Router User Guide 5.4.3 MAC Clone 5.5.1 DHCP Settings 5.5DHCPDHCP yDHCP settings yDHCP Clients List TL-R402M Cable/DSL Router User Guide 5.5.2 DHCP Clients List 5.5.3 Address ReservationTL-R402M Cable/DSL Router User Guide Figure 5-13Address Reservation TL-R402M Cable/DSL Router User Guide 5.6.1 Virtual Servers 5.6ForwardingTL-R402M Cable/DSL Router User Guide Forwarding yVirtual Servers yPort Triggering yDMZ TL-R402M Cable/DSL Router User Guide 5.6.2 Port Triggering Figure 5-16Port Triggering TL-R402M Cable/DSL Router User Guide TL-R402M Cable/DSL Router User Guide 5.6.3 DMZ 5.6.4 UPnP 5.7SecurityTL-R402M Cable/DSL Router User Guide Security yFirewall yIP Filter yDomain Filter yMAC 5.7.1 Firewall 5.7.2 IP Address FilteringTL-R402M Cable/DSL Router User Guide Figure 5-21IP Address Filtering TL-R402M Cable/DSL Router User Guide 5.7.3 Domain Filtering TL-R402M Cable/DSL Router User GuideFor example TL-R402M Cable/DSL Router User Guide Figure 5-23Domain FilteringFor example TL-R402M Cable/DSL Router User Guide 5.7.4 MAC Filtering 5.7.5 Remote Management TL-R402M Cable/DSL Router User GuideFox example 5.7.6 Ping from WAN 5.8 Static RoutingTL-R402M Cable/DSL Router User Guide To add static routing entries 5.9.1 Firmware 5.9System ToolsTL-R402M Cable/DSL Router User Guide To modify an existing entry TL-R402M Cable/DSL Router User Guide 5.9.2 Factory Defaults 5.9.3 Reboot 5.9.4 PasswordTL-R402M Cable/DSL Router User Guide TL-R402M Cable/DSL Router User Guide 5.9.5 Log TL-R402M Cable/DSL Router User Guide Appendix A FAQ 3.I want to use Netmeeting, what do I need to do? TL-R402M Cable/DSL Router User Guide Figure 5 DMZ TL-R402M Cable/DSL Router User Guide 1.Install TCP/IP component Appendix B Configuring the PCs2.Configure TCP/IP for your computer TL-R402M Cable/DSL Router User Guide Assigned by DHCP Sever TL-R402M Cable/DSL Router User Guide Setting IP address manually Figure 13 DNS Configuration tabTL-R402M Cable/DSL Router User Guide Figure 12 Gateway tab Figure 14 IP Address tab TL-R402M Cable/DSL Router User Guide TL-R402M Cable/DSL Router User Guide Figure 16 DNS Configuration tab TL-R402M Appendix C SpecificationsCable/DSL Router User Guide General TL-R402M Cable/DSL Router User Guide Appendix D Glossary TL-R402M Cable/DSL Router User Guide Appendix E Contact Information