Manuals / Tyan Computer / Computer Equipment / Computer Hardware

Tyan Computer Thunder i7505, S2665 warranty Before you begin… Check the box contents

Models: Thunder i7505 S2665

1 40

Download 40 pages 1.04 Kb

Page 3

Before you begin…

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1x Thunder i7505 S2665

1x 34-Pin floppy drive cable

1x Ultra160/320 LVD SCSI cable (if optional SCSI included)

1x Ultra-D M A-100/66/33 IDE cable

1x Thunder i7505 S2665 User’s Manual

1x TYAN driver CD

1x Adaptec Ultra160/Ultra320 SCSI driver diskette (if optional SCSI included)

1x I/O shield

2X CPU retention

If any of these items are missing, please contact your vendor/dealer fo r replacement before continuing with the installation process.

3

http://www.TYAN.com

Image 3

Tyan Computer Thunder i7505, S2665 warranty Before you begin… Check the box contents

Contents

Adaptec is a trademark of Adaptec Inc ThunderS2665 RevisionTable of Contents Before you begin… Check the box contents Chapter 1 Introduction Form Factor Integrated PCI IDEIntegrated I/O System ManagementDO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED Chapter 2 Board InstallationInstallation How to install our products right….the first timeThe following is an image of the S2665 2.0 - BoardJumper Legend 2.1 - Board Parts, Jumpers and ConnectorsTo indicate where the location of pin-1 To indicate where the location of pin-1Page 2.3 - AUX Audio Connector J8 and CD Audio Connector J16 To disable PS/2 devices’ ACPI wake up function OPEN Default To enable PCI- X capability on Slot-A 2.14 - LCD Connector J69 CLOSE Pins 1 and 2 Defaultpin-1 CLOSE Pins 2 and 2.13 - IEEE 1394 Connector J66Intrusion detection low asserted Intrusion cable detection low asserted2.20 - OEM Reserved Connectors and Jumpers 2.18 - Front Panel Connector J74Signal Description Signal Descriptionv supported v supportedX unsupported 2.22 - Installing the MemoryMemory Installation Procedure 2.23 - Installing the Processors and Heatsinks Heatsink InstallationREMINDER b. Insert Black securing peg into bracket holes c. Insert White locking peg into Black securing pegd. Repeat process to mount all other brackets 2.24 - Installing Add- In Cards Finishing Installing the Heatsinka. Audio Port Line In Jack 2.25 - Connecting External Devicesc. SPDIF SPDIF RCA connector d. RJ45 LAN Port e. IEEE IEEE 1394 connector2.26- Installing the Power Supply 2.27 - Attaching IDE and Floppy Drive Cables 2.28 - Finishing Up To select an item Chapter 3 BIOS3.0 - BIOS Setup Utility Main√ arrow keys 3.1 - BIOS Menu Bar3.2 - BIOS Legend Bar Function3.3 - BIOS Main Menu 3.4 - BIOS Advanced Menu 3.4.4 - IDE Devices Sub -Menu Feature 4Clear Supervisor Password ROMs during system boot up Default Primary Video AdapterDisplay Option ROM Message 3.8.1 - Exit Saving Changes 3.8 - BIOS Exit Menu3.8.3 - Load Setup Defaults Exit4.2 Flash Utility Chapter 4 DiagnosticsCPU, Memory, Video 4.1 Beep CodesAppendix I Glossary Firmware low-level software that controls the system hardware IDE INT IDE Interrupt a hardware interrupt signal that goes to the IDE Sleep/Suspend mode in this mode, all devices except the CPU shut down VGA Video Graphics Arraythe PC video display standardV-SYNC controls the vertical scanning properties of the monitor Technical Support Notice for the USA Document # D1491