Tyan Computer Trinity 371 Motherboard, Tyan S1857 - page 54

http://www.tyan.com

54

Chapter 3

BIOS Configuration

* Setting option not selectable.

ACPI Aware O/S

Set this option to Yes to enable Advanced Configuration and Power Interface

(ACPI) BIOS for an ACPI-aware operating system.

Power Management/APM

Set this option to Enabled to enable the chipset power management and APM

(Advanced Power Management) features. The settings are Enabled or Dis-

abled.

Power Button Function

This option specifies how the power button mounted externally on the

computer chassis is used. See Soft Power Connector on page 20 for more

information. The settings are shown in the table below.

Green PC Monitor Power State

This option specifies the power state that the green PC-compliant video

Setting Option Optimal Default Fail-Safe Default

Device 6 (Serial po rt 1) Monito r Monito r

Device 7 (Serial po rt 2) Monito r Monito r

Device 8 (Parallel po rt) Monito r Monito r

Device 5 (Flo ppy disk) M onitor M onitor

Device 0 (Primary master IDE) Monito r Monitor

Device 1 (Primary slave IDE) Monito r Monitor

Device 2 (Seco ndary master IDE) Monito r Monito r

Device 3 (Seco ndary slave IDE) Monito r Monito r

LAN Wake-up Fo r Addon LAN Disabled Disabled

LAN Wake-up Fo r Onboard LAN Disabled Disabled

PC 98 Po wer LED Enabled Enabled

Fan OFF at Suspend Enabled Enabled

RTC Wake-up Disabled Dis abled

*Hou r N/A N/A

*Min ute N/A N/A

gnitteSnoitpircseD

ffO/nO.fforonoretupmocehtsnrutnottubrewopehtgnihsuP

dnepsuS .edomrewopnOlluFroedomdnepsuSniretupmocehtsecalpnottubrewopehtgnihsuP

Contents

Main Tyan S1857 Trinity 371 PRINTED IN TAIWAN Motherboard Users Manual Revision 1.20 Table of Contents Page Overview chapter 1 Introduction Icons S1857-B & S1857A-B BX Chipset Hardware Specifications/Features Software Specifications S1857 & S1857A VIA Chipset Hardware Specifications/Features Software Specifications Technical Support Returning Merchandise for Service Page chapter 2 Board Installation Unpacking Installation How to install our products right...the first time. Installation Steps Quick References for Jumpers The tiny 1s next to jumpers of 3 pins or more indicate the position of pin 1 for that jumper. Figure 2-3 : Map of Motherboard Jumpers Slot 1 Type CPU DIMM bank 2 PCI slot 1 Flash BIOS Figure 2-4 : Map of S1857 Features 1. Setting Jumpers 1-A. CPU Speed Settings (Jumpers JP10, JP11, JP12, JP13) JP12, JP13 Page 1-H Fan Speed Detect 1-I Soft Power Connector 1-J Sound disable (JP17) 1-K. Reserved Factory Header (J18) 1-L Hardware Reset Switch Connector Installation 1-M Creative Labs Audio Connectors 1-N External SMI 1-O Intrusion Alarm Connector 1-P Power LED Connector 2. Mounting the Motherboard in the Chassis 3. Installing Memory Page Page Page 4. Installing the CPU and Cooling Fan Figure 2-8 Installing CPU Retention Modules Page Page 5. Connecting IDE and Floppy Drives Page Page 6. Connecting the Power Supply 7. Installing Add-on Cards 8. Connecting PS/2, USB, Serial & Parallel Devices ONBOARD Connecting Com and Printer Ports chapter 3 BIOS Configuration The AMIBIOS Setup screen is shown below. Main Setup Page epyTerugifnoCotwoH Page Default Settings Advanced CMOS Setup Advanced CMOS Setup Default Settings Chart Setting Option Optimal Default Fail-Sa fe Default Settings Chart (Continued) Advanced Setup gnitteSnoitpircseD Setting Option Optimal Default Fail-Safe Default Page Page Page Chipset Setup Advanced Chipset Setup Default Settings Chart Setting Option Optimal Default Fail-Safe Default Settings Chart (continued) Setting Option Optimal Default Fail-Safe Default Page Page Page Page Power Management Setup Power Management Setup Default Settings Chart Setting Option Optimal Defaul t Fail-Safe Default Page Page Page Plug and Play Setup Plug and Play Setup Default Settings Chart * Setting option is not selectable Setting Option Optimal Default Fail-Sa fe Default Page Page Page Peripheral Setup Peripheral Setup Default Settings Chart Setting Option Optimal Default Fail-Sa fe Default Page edoMnoitpircseD Page Supervisor and User Security Language Utility Flash Writer Utility Need BIOS upgrade? Visit TYAN @ http://www.tyan.com Page chapter 4 System Resources Beep Codes SYSTEM Troubleshooting System Problems If the computer beeps... then... Chapter 4 System Resources Displayed Error Messages ERROR Message Line 1 ERROR Message Line 2 Press <F1> to continue RUN SETUP UTILITY may also appear. Press <F1> to run AwardBIOS Setup if this message appears. egasseMrorrEnoitanalpxE SYSTEM ACPI AGP AT ATAPI ATX Appendix 1 Glossary Page Page Page Page Page Page Appendix 2 Retention Module Installation Page Page Installing SECC2 CPUs - Option 2 Page Award BIOS Configuration BIOS 2 Introduction to Setup Starting Setup Setup Keys Getting Help In Case of Problems Page Setup Variations Main Setup Menu Page Standard CMOS Setup Page Page BIOS Features Setup ROM PCI/ISA BIOS (2A5LET59) BIOS FEATURES SETUP BIOS Feature Setup - Default Settings Chart Page Page Page Chipset Features Setup Page Page Power Management Setup Power Management Setup - Default Settings Chart Settings Chart (Continued) ROM PCI/ISA BIOS (2A5LET5A) POWER MANAGEMENT SETUP BIOS 2 Award BIOS Configuration Page Page Page Page PnP/PCI Configuration PnP / PCI Configuration - Default Settings Chart ROM PCI/ISA BIOS (2A5LET5A) PNP/PCI CONFIGURATION Page Page Integrated Peripherals Integrated Peripherals - Default Settings Chart ROM PCI/ISA BIOS (2A5LET59) INTEGRATED PERIPHERALS BIOS 2 Award BIOS Configuration Page Page User Password Flash Writer Utility Page Page Document # D1367-120 S1857 Trinity 371 Jumper Settings Quick Reference See pages 15-20 for details on Jumpers. 1-A. CPU Speed Settings (Jumpers JP10, JP11, JP12, JP13) 2-13-2 BUS Speed Settings (FS0, FS1) Clear CMOS and Reset Password (Jumper JP2)