Tyan Computer Trinity 371 Motherboard, Tyan S1857 - page 63

S1857 Trinity 371

63

Settings Chart (Continued)

* Setting Option not selectable

Power Interruption

The settings are Enabled or Disabled.

Overclock Warning Message

When enabled, this option sends a warning message if the CPU is overclocked.

The settings are Enabled or Disabled.

Keyboard Wake-up Function

This option allows for system power-on via the keyboard. The settings are

Enabled or Disabled.

Mouse Wake-up Function

This option allows for system power-on via the Mouse. The settings are

Enabled or Disabled.

Onboard FDC

Set this option to Enabled to enable the floppy drive controller on the mother-

board. The settings are Auto, Enabled, or Disabled.

Setting Option Optimal Default Fail-Sa fe Default

Fan2 Speed N/A N/A

Onboard FDC Enabled Enabled

Onboard Serial Po rt 1 3F8h 3F8h

Onboard Serial Po rt 2 2F8h 2F8h

Serial Port 2 M ode Nor mal No rmal

*IR Du plex Mode N/A N/A

Onboard Parallel P ort 378 378

Paralle l Por t Mo de ECP ECP

*EPP Version N/A N/A

Para llel P ort IRQ 7 7

*Parallel Por t DM A Chan nel 3 3

Onboard IDE Both Both

Note: The CPU fan activates after the VGA card is initalized and not when the

system boots up, therefore you may experience a 5 second delay before the

CPU fan is enabled.

BIOS

Contents

Main Tyan S1857 Trinity 371 PRINTED IN TAIWAN Motherboard Users Manual Revision 1.20 Table of Contents Page Overview chapter 1 Introduction Icons S1857-B & S1857A-B BX Chipset Hardware Specifications/Features Software Specifications S1857 & S1857A VIA Chipset Hardware Specifications/Features Software Specifications Technical Support Returning Merchandise for Service Page chapter 2 Board Installation Unpacking Installation How to install our products right...the first time. Installation Steps Quick References for Jumpers The tiny 1s next to jumpers of 3 pins or more indicate the position of pin 1 for that jumper. Figure 2-3 : Map of Motherboard Jumpers Slot 1 Type CPU DIMM bank 2 PCI slot 1 Flash BIOS Figure 2-4 : Map of S1857 Features 1. Setting Jumpers 1-A. CPU Speed Settings (Jumpers JP10, JP11, JP12, JP13) JP12, JP13 Page 1-H Fan Speed Detect 1-I Soft Power Connector 1-J Sound disable (JP17) 1-K. Reserved Factory Header (J18) 1-L Hardware Reset Switch Connector Installation 1-M Creative Labs Audio Connectors 1-N External SMI 1-O Intrusion Alarm Connector 1-P Power LED Connector 2. Mounting the Motherboard in the Chassis 3. Installing Memory Page Page Page 4. Installing the CPU and Cooling Fan Figure 2-8 Installing CPU Retention Modules Page Page 5. Connecting IDE and Floppy Drives Page Page 6. Connecting the Power Supply 7. Installing Add-on Cards 8. Connecting PS/2, USB, Serial & Parallel Devices ONBOARD Connecting Com and Printer Ports chapter 3 BIOS Configuration The AMIBIOS Setup screen is shown below. Main Setup Page epyTerugifnoCotwoH Page Default Settings Advanced CMOS Setup Advanced CMOS Setup Default Settings Chart Setting Option Optimal Default Fail-Sa fe Default Settings Chart (Continued) Advanced Setup gnitteSnoitpircseD Setting Option Optimal Default Fail-Safe Default Page Page Page Chipset Setup Advanced Chipset Setup Default Settings Chart Setting Option Optimal Default Fail-Safe Default Settings Chart (continued) Setting Option Optimal Default Fail-Safe Default Page Page Page Page Power Management Setup Power Management Setup Default Settings Chart Setting Option Optimal Defaul t Fail-Safe Default Page Page Page Plug and Play Setup Plug and Play Setup Default Settings Chart * Setting option is not selectable Setting Option Optimal Default Fail-Sa fe Default Page Page Page Peripheral Setup Peripheral Setup Default Settings Chart Setting Option Optimal Default Fail-Sa fe Default Page edoMnoitpircseD Page Supervisor and User Security Language Utility Flash Writer Utility Need BIOS upgrade? Visit TYAN @ http://www.tyan.com Page chapter 4 System Resources Beep Codes SYSTEM Troubleshooting System Problems If the computer beeps... then... Chapter 4 System Resources Displayed Error Messages ERROR Message Line 1 ERROR Message Line 2 Press <F1> to continue RUN SETUP UTILITY may also appear. Press <F1> to run AwardBIOS Setup if this message appears. egasseMrorrEnoitanalpxE SYSTEM ACPI AGP AT ATAPI ATX Appendix 1 Glossary Page Page Page Page Page Page Appendix 2 Retention Module Installation Page Page Installing SECC2 CPUs - Option 2 Page Award BIOS Configuration BIOS 2 Introduction to Setup Starting Setup Setup Keys Getting Help In Case of Problems Page Setup Variations Main Setup Menu Page Standard CMOS Setup Page Page BIOS Features Setup ROM PCI/ISA BIOS (2A5LET59) BIOS FEATURES SETUP BIOS Feature Setup - Default Settings Chart Page Page Page Chipset Features Setup Page Page Power Management Setup Power Management Setup - Default Settings Chart Settings Chart (Continued) ROM PCI/ISA BIOS (2A5LET5A) POWER MANAGEMENT SETUP BIOS 2 Award BIOS Configuration Page Page Page Page PnP/PCI Configuration PnP / PCI Configuration - Default Settings Chart ROM PCI/ISA BIOS (2A5LET5A) PNP/PCI CONFIGURATION Page Page Integrated Peripherals Integrated Peripherals - Default Settings Chart ROM PCI/ISA BIOS (2A5LET59) INTEGRATED PERIPHERALS BIOS 2 Award BIOS Configuration Page Page User Password Flash Writer Utility Page Page Document # D1367-120 S1857 Trinity 371 Jumper Settings Quick Reference See pages 15-20 for details on Jumpers. 1-A. CPU Speed Settings (Jumpers JP10, JP11, JP12, JP13) 2-13-2 BUS Speed Settings (FS0, FS1) Clear CMOS and Reset Password (Jumper JP2)