Tyan Computer Trinity 371 Motherboard, Tyan S1857 - page 65

S1857 Trinity 371

65

Parallel Port Mode

This option specifies the parallel port mode. The settings are:

EPP Version

This option specifies the Enhanced Parallel Port specification version number

that is used in the system. This option only appears if the Parallel Port Mode

option is set to EPP. The settings are 1.7 or 1.9. Version 1.9 is common on

newer devices; consult your devices user information for the appropriate port

type. There are no default settings.

Parallel Port IRQ

This option specifies the IRQ used by the parallel port, and only appears if

OnBoard Parallel Port is set to 278 or 378. The settings are 5 or 7.

Parallel Port DMA Channel

This option is only available if the setting for the Parallel Port Mode option is

set to ECP and the OnBoard Parallel Port option is set to 378, 278, or 3BC. This

option sets the DMA channel used by the parallel port. The settings are 0

through 7 in increments of one.

Onboard IDE

This option specifies the IDE channel used by the onboard IDE controller. The

settings are Disabled, Primary, Secondary, or Both.

gnitteSnoitpircseD

lamroN.desusiedomtroplellaraplamronehT

riD-iB.troplellarapehtnosrefsnartlanoitceridibtroppusotgnittessihtesU

PPE

troPlellaraPdecnahnEehtoterehdatahtsecivedhtiwdesuebnactroplellarapehT

cirtemmysaedivorpotslangistroplellarapgnitsixeehtsesuPPE.snoitacificeps)PPE(

.ecivedtsohehtybnevirdrefsnartatadlanoitceridib

PCE

troPseitilibapaCdednetxEehtoterehdatahtsecivedhtiwdesuebnactroplellarapehT

pufosetarrefsnartatadeveihcaotlocotorpAMDehtsesuPCE.snoitacificeps)PCE(

.noitacinummoclanoitceridibcirtemmyssedivorpPCE.dnocesrepstibageM5.2ot

BIOS

Contents

Main Tyan S1857 Trinity 371 PRINTED IN TAIWAN Motherboard Users Manual Revision 1.20 Table of Contents Page Overview chapter 1 Introduction Icons S1857-B & S1857A-B BX Chipset Hardware Specifications/Features Software Specifications S1857 & S1857A VIA Chipset Hardware Specifications/Features Software Specifications Technical Support Returning Merchandise for Service Page chapter 2 Board Installation Unpacking Installation How to install our products right...the first time. Installation Steps Quick References for Jumpers The tiny 1s next to jumpers of 3 pins or more indicate the position of pin 1 for that jumper. Figure 2-3 : Map of Motherboard Jumpers Slot 1 Type CPU DIMM bank 2 PCI slot 1 Flash BIOS Figure 2-4 : Map of S1857 Features 1. Setting Jumpers 1-A. CPU Speed Settings (Jumpers JP10, JP11, JP12, JP13) JP12, JP13 Page 1-H Fan Speed Detect 1-I Soft Power Connector 1-J Sound disable (JP17) 1-K. Reserved Factory Header (J18) 1-L Hardware Reset Switch Connector Installation 1-M Creative Labs Audio Connectors 1-N External SMI 1-O Intrusion Alarm Connector 1-P Power LED Connector 2. Mounting the Motherboard in the Chassis 3. Installing Memory Page Page Page 4. Installing the CPU and Cooling Fan Figure 2-8 Installing CPU Retention Modules Page Page 5. Connecting IDE and Floppy Drives Page Page 6. Connecting the Power Supply 7. Installing Add-on Cards 8. Connecting PS/2, USB, Serial & Parallel Devices ONBOARD Connecting Com and Printer Ports chapter 3 BIOS Configuration The AMIBIOS Setup screen is shown below. Main Setup Page epyTerugifnoCotwoH Page Default Settings Advanced CMOS Setup Advanced CMOS Setup Default Settings Chart Setting Option Optimal Default Fail-Sa fe Default Settings Chart (Continued) Advanced Setup gnitteSnoitpircseD Setting Option Optimal Default Fail-Safe Default Page Page Page Chipset Setup Advanced Chipset Setup Default Settings Chart Setting Option Optimal Default Fail-Safe Default Settings Chart (continued) Setting Option Optimal Default Fail-Safe Default Page Page Page Page Power Management Setup Power Management Setup Default Settings Chart Setting Option Optimal Defaul t Fail-Safe Default Page Page Page Plug and Play Setup Plug and Play Setup Default Settings Chart * Setting option is not selectable Setting Option Optimal Default Fail-Sa fe Default Page Page Page Peripheral Setup Peripheral Setup Default Settings Chart Setting Option Optimal Default Fail-Sa fe Default Page edoMnoitpircseD Page Supervisor and User Security Language Utility Flash Writer Utility Need BIOS upgrade? Visit TYAN @ http://www.tyan.com Page chapter 4 System Resources Beep Codes SYSTEM Troubleshooting System Problems If the computer beeps... then... Chapter 4 System Resources Displayed Error Messages ERROR Message Line 1 ERROR Message Line 2 Press <F1> to continue RUN SETUP UTILITY may also appear. Press <F1> to run AwardBIOS Setup if this message appears. egasseMrorrEnoitanalpxE SYSTEM ACPI AGP AT ATAPI ATX Appendix 1 Glossary Page Page Page Page Page Page Appendix 2 Retention Module Installation Page Page Installing SECC2 CPUs - Option 2 Page Award BIOS Configuration BIOS 2 Introduction to Setup Starting Setup Setup Keys Getting Help In Case of Problems Page Setup Variations Main Setup Menu Page Standard CMOS Setup Page Page BIOS Features Setup ROM PCI/ISA BIOS (2A5LET59) BIOS FEATURES SETUP BIOS Feature Setup - Default Settings Chart Page Page Page Chipset Features Setup Page Page Power Management Setup Power Management Setup - Default Settings Chart Settings Chart (Continued) ROM PCI/ISA BIOS (2A5LET5A) POWER MANAGEMENT SETUP BIOS 2 Award BIOS Configuration Page Page Page Page PnP/PCI Configuration PnP / PCI Configuration - Default Settings Chart ROM PCI/ISA BIOS (2A5LET5A) PNP/PCI CONFIGURATION Page Page Integrated Peripherals Integrated Peripherals - Default Settings Chart ROM PCI/ISA BIOS (2A5LET59) INTEGRATED PERIPHERALS BIOS 2 Award BIOS Configuration Page Page User Password Flash Writer Utility Page Page Document # D1367-120 S1857 Trinity 371 Jumper Settings Quick Reference See pages 15-20 for details on Jumpers. 1-A. CPU Speed Settings (Jumpers JP10, JP11, JP12, JP13) 2-13-2 BUS Speed Settings (FS0, FS1) Clear CMOS and Reset Password (Jumper JP2)