Tyan Computer Trinity 371 Motherboard, Tyan S1857 edoMnoitpircseD

http://www.tyan.com

64

Chapter 3

BIOS Configuration

Onboard Serial Port1

This option specifies the base I/O port address of serial port 1. The settings

are Auto, Disabled, 3F8h, 2F8h, 3E8h, or 2E8h.

Onboard Serial Port2

This option specifies the base I/O port address of serial port 2. The settings

are Auto, Disabled, 3F8h, 2F8h, 3E8h, or 2E8h.

Serial Port2 Mode

This option specifies the operating mode for serial port 2. This option will not

appear if the Onboard Serial Port2 option is set to Disabled, or is set to Auto

and your system does not have an onboard serial port 2. The settings are

Normal, Sharp-IR, IrDA, and Consumer.

IR Transmission Mode

This option specifies the infrared transmission method. This option will not

appear if the Serial Port2 Mode option is set to Normal. The settings are Full or

Half.

OnBoard Parallel Port

This option specifies the base I/O port address of the parallel port on the

motherboard. The settings are Auto, Disabled, 378, or 278.

edoMnoitpircseD

xelpuDlluF

tonlliwdnesuoyatadynA.ecnotasnoitceridowtnidettimsnartsiataD

ecivedrehtoehtybdeviecerneebsahtilitnuneercsruoynoraeppa

.sedomowtehtforetsafehtsixelpudlluF.uoyotkcabtnesdna

xelpuDflaH

dnesuoyatadynA.emitatanoitceridenoylnonidettimsnartsiataD

reisaesiedomxelpudflaH.neercsruoynodeyalpsidyltnatsnieblliw

llufeldnahnacsecivedelbapac-RIllatoN.etucexeotsecivedehtrof

.edomxelpud

Contents

Main Tyan S1857 Trinity 371 PRINTED IN TAIWAN Motherboard Users Manual Revision 1.20 Table of Contents Page Overview chapter 1 Introduction Icons S1857-B & S1857A-B BX Chipset Hardware Specifications/Features Software Specifications S1857 & S1857A VIA Chipset Hardware Specifications/Features Software Specifications Technical Support Returning Merchandise for Service Page chapter 2 Board Installation Unpacking Installation How to install our products right...the first time. Installation Steps Quick References for Jumpers The tiny 1s next to jumpers of 3 pins or more indicate the position of pin 1 for that jumper. Figure 2-3 : Map of Motherboard Jumpers Slot 1 Type CPU DIMM bank 2 PCI slot 1 Flash BIOS Figure 2-4 : Map of S1857 Features 1. Setting Jumpers 1-A. CPU Speed Settings (Jumpers JP10, JP11, JP12, JP13) JP12, JP13 Page 1-H Fan Speed Detect 1-I Soft Power Connector 1-J Sound disable (JP17) 1-K. Reserved Factory Header (J18) 1-L Hardware Reset Switch Connector Installation 1-M Creative Labs Audio Connectors 1-N External SMI 1-O Intrusion Alarm Connector 1-P Power LED Connector 2. Mounting the Motherboard in the Chassis 3. Installing Memory Page Page Page 4. Installing the CPU and Cooling Fan Figure 2-8 Installing CPU Retention Modules Page Page 5. Connecting IDE and Floppy Drives Page Page 6. Connecting the Power Supply 7. Installing Add-on Cards 8. Connecting PS/2, USB, Serial & Parallel Devices ONBOARD Connecting Com and Printer Ports chapter 3 BIOS Configuration The AMIBIOS Setup screen is shown below. Main Setup Page epyTerugifnoCotwoH Page Default Settings Advanced CMOS Setup Advanced CMOS Setup Default Settings Chart Setting Option Optimal Default Fail-Sa fe Default Settings Chart (Continued) Advanced Setup gnitteSnoitpircseD Setting Option Optimal Default Fail-Safe Default Page Page Page Chipset Setup Advanced Chipset Setup Default Settings Chart Setting Option Optimal Default Fail-Safe Default Settings Chart (continued) Setting Option Optimal Default Fail-Safe Default Page Page Page Page Power Management Setup Power Management Setup Default Settings Chart Setting Option Optimal Defaul t Fail-Safe Default Page Page Page Plug and Play Setup Plug and Play Setup Default Settings Chart * Setting option is not selectable Setting Option Optimal Default Fail-Sa fe Default Page Page Page Peripheral Setup Peripheral Setup Default Settings Chart Setting Option Optimal Default Fail-Sa fe Default Page edoMnoitpircseD Page Supervisor and User Security Language Utility Flash Writer Utility Need BIOS upgrade? Visit TYAN @ http://www.tyan.com Page chapter 4 System Resources Beep Codes SYSTEM Troubleshooting System Problems If the computer beeps... then... Chapter 4 System Resources Displayed Error Messages ERROR Message Line 1 ERROR Message Line 2 Press <F1> to continue RUN SETUP UTILITY may also appear. Press <F1> to run AwardBIOS Setup if this message appears. egasseMrorrEnoitanalpxE SYSTEM ACPI AGP AT ATAPI ATX Appendix 1 Glossary Page Page Page Page Page Page Appendix 2 Retention Module Installation Page Page Installing SECC2 CPUs - Option 2 Page Award BIOS Configuration BIOS 2 Introduction to Setup Starting Setup Setup Keys Getting Help In Case of Problems Page Setup Variations Main Setup Menu Page Standard CMOS Setup Page Page BIOS Features Setup ROM PCI/ISA BIOS (2A5LET59) BIOS FEATURES SETUP BIOS Feature Setup - Default Settings Chart Page Page Page Chipset Features Setup Page Page Power Management Setup Power Management Setup - Default Settings Chart Settings Chart (Continued) ROM PCI/ISA BIOS (2A5LET5A) POWER MANAGEMENT SETUP BIOS 2 Award BIOS Configuration Page Page Page Page PnP/PCI Configuration PnP / PCI Configuration - Default Settings Chart ROM PCI/ISA BIOS (2A5LET5A) PNP/PCI CONFIGURATION Page Page Integrated Peripherals Integrated Peripherals - Default Settings Chart ROM PCI/ISA BIOS (2A5LET59) INTEGRATED PERIPHERALS BIOS 2 Award BIOS Configuration Page Page User Password Flash Writer Utility Page Page Document # D1367-120 S1857 Trinity 371 Jumper Settings Quick Reference See pages 15-20 for details on Jumpers. 1-A. CPU Speed Settings (Jumpers JP10, JP11, JP12, JP13) 2-13-2 BUS Speed Settings (FS0, FS1) Clear CMOS and Reset Password (Jumper JP2)