DV360/580 Series Direct Vent Gas Fireplace
For Use in Mobile Homes: Model DV360RMH
This appliance may be installed as an OEM installation in a manufactured home (US only), or a mobile home; it must be installed in accordance with the manufacturer’s instructions and the manufactured home construction and safety standard Title 24 CFR Part 3280, or Standard for Installation in Mobile Homes CAN/ CSA Z240 MH.
This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is sup- plied with the appliance.
This gas fireplace should be installed by a qualified in- staller in accordance with local building codes, and with current
CSA Z 240.4 Canada.
A manufactured home (US only) or mobile home
OEM installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR Part 3280, or when such a standard is not applicable, the Standard for Manufactured Home Installations
ANSI/NCSBCS A225.1, or Standard for Gas Equipped Recreational Vehicles and Mobile Housing
CSA Z240.4.
The appliance when installed, must be electrically grounded in accordance with local codes or, in the ab- sence of local codes, with the current National Electri- cal Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.
FOR SAFE INSTALLATION AND OPERATION PLEASE NOTE THE FOLLOWING:
1.This fireplace gives off high temperatures and should be located out of high traffic areas and away from furniture and draperies.
2.Children and adults should be alerted to the hazards of fireplace high surface temperatures and should stay away to avoid burns or ignition of clothing.
3.Children should be carefully supervised when in the same room as your fireplace.
4.Under no circumstances should this fireplace be modified. Parts removed for servicing should be replaced prior to operating this fireplace again.
5.Installation and any repairs to fireplace should be performed by qualified installer, service agency or gas supplier. A professional service person should be contacted to inspect fireplace annually. More frequent cleaning may be required due to excess lint and dust from carpeting, bedding material, etc.
6.Control compartments, burners and air passages in this fireplace should be kept clean and free of dust and lint. Make sure that the gas valve and pilot light are turned off before you attempt to clean this fireplace.
7.The venting system (chimney) of this fireplace should be checked at least once a year and if needed your venting system should be cleaned.
8.Keep the area around your fireplace clear of com- bustible materials, gasoline and other flammable vapor and liquids. This fireplace should not be used as a drying rack for clothing, nor should Christmas stockings or decorations be hung on or around the fireplace.
9.Under no circumstances should any solid fuels (wood, coal, paper or cardboard etc.) be used in this fireplace.
10.The flow of combustion and ventilation air must not be obstructed in any way.
11.When the fireplace is installed directly on carpet- ing, vinyl tile or any combustible material other than wood, the fireplace must be installed on a metal or wood panel extending the full width and depth of the fireplace.
12.This fireplace requires adequate ventilation and combustion air to operate properly.
CFM Corporation Model DV360RMH must be firmly attached to the building.
Conversion Instructions
1.Discount power to unit and shut off the gas supply.
2.Remove the window frame assembly (see ‘Window Frame Assembly’ section).
3.Carefully remove the logs.
4.Remove the pilot assembly from bracket.
5.Remove the screws which are holding the burner housing assembly in place.
6.Remove the burner housing assembly.
7.Remove the main and front orifice and replace with the orifice supplied in the conversion kit. Use the small orifice size for the front burner and the bigger orifice size for the main burner.
8.Remove the compression fitting which holds the alu- minium tubing in the pilot assembly. This will reveal the pilot orifice which must be replaced with the one provided in the conversion kit.
9a. Units with SIT valve (Refer to illustrations in the installation instructions supplied with the kit):
50 | 20010667 |
