Radiance Vent-Free Gas Heater

8.Install glass frame assembly by resting the bot- tom edge of the frame on support brackets below the front opening of the firebox. Swing the top edge of the assembly toward the firebox, and center it. Fasten by closing the latches over the top left and right edges of the frame. (Fig. 22)

ST672

Fig. 22 Set glass frame in place and secure latches.

Connect the Gas Supply Line

Check the Rating Plate attached by a steel cable to the firebox, to confirm that you have the appropriate firebox

for the type of fuel to be used.

This appliance should only be connected by a qualified gas technician. Test to confirm manifold pressures as specified below.

The Radiance Heater and its individual shutoff valve must be disconnected from the gas supply piping during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).

The Radiance Heater must be isolated from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressure equal to or less than 1/2 psig.

There must be a gas shutoff between the stove and the supply.

In order to connect Natural Gas, use a fitting with 3/8” NPT nipple on the valve side and 1/2” natural gas supply line with an input of 35,000 BTUs at a manifold pressure of 3.5” and minimum inlet sup- ply for adjustment of 5.5” w.c.

In order to connect Propane, use a fitting with 3/8” NPT nipple on the valve side and 1/2” propane gas supply line with an input of 35,000 BTUs at a mani- fold pressure of 11.0” and minimum inlet supply for adjustment of 11.0” w.c.

Gas connection should be made in accordance with current National Fuel Gas Code, ANSI Z223.1. Since some municipalities have additional local codes, be sure to consult you local authority.

Connect the gas supply and test for leaks. Use a 50/50 solution of liquid soap and water to test for leaks at gas fittings and joints. NEVER test with an open flame.

Light the pilot according to the directions on page 16, before going to the next step.

CAUTION

This appliance should only be connected by a qualified gas technician. Test to confirm manifold pressures as specified below.

The Radiance Heater and its individual shutoff valve must be disconnected from the gas supply piping during any pressure testing of that system at test pressures in excess of 1/2 psig (3.5 kPa).

The Radiance Heater must be isolated from the gas supply piping system by closing its indi- vidual manual shutoff valve during any pressure testing of the gas supply piping system at test pressure equal to or less than 1/2 psig.

There must be a gas shutoff between the stove and the supply.

In order to connect Natural Gas, use a fitting with 1/2” NPT on the valve side and 1/2” natural gas supply line with an input of 35,000 BTUs at a manifold pressure of 3.5” between minimum inlet supply of 5.5” w.c. and maximum of 14.0” w.c.

In order to connect Propane, use a fitting with 1/2” NPT on the valve side and 1/2” propane gas sup- ply line with an input of 35,000 BTUs at a manifold pressure of 11.0” between a minimum inlet supply of 11.0” w.c. and maximum of 14.0” w.c.

Install Log Set

1.Remove the logs from their packaging, and inspect each piece for damage. DO NOT INSTALL DAM-

AGED LOGS.

2.Install the rear left log by placing it on the sheet metal shelf at the back of the firebox. (Fig. 23) The log should touch the back wall of the firebox. Slide the log to the left until the left side lines up with the left bracket. (Fig. 23) When the log is in place the left front corner of the log should rest on the decora- tive grate.

3.Install the rear right log by placing it on the sheet metal shelf at the back toward the right. Make sure the right side of the log lines up with the right bracket. (Fig. 23) NOTE: When the right and left rear logs are in place, they should touch the back of the firebox and each other.

4.Install the right log by engaging hole on the bottom with pin on the right rear log. (Fig. 23) Set the bottom of the log on the bracket and bring forward to come in contact with decorative grate on right.

14

20004555

Page 13 Page 15
Page 14
Image 14
Vermont Casting 3370, RUVSOD: 3357, thru 3379, 3358 manual Connect the Gas Supply Line, Install Log Set, Aged Logs
Page 13 Page 15

3358, RUVSOD: 3357, 3370, thru 3379 specifications

Vermont Casting's RUVSOD series, comprising models 3357, 3358, 3370, and 3379, is widely recognized for its exceptional performance and timeless design. These wood stoves are crafted from durable cast iron, ensuring longevity and optimal heat retention. Each model in the RUVSOD line showcases Vermont Casting's commitment to quality, efficiency, and aesthetic appeal.

One of the key features of the RUVSOD series is its remarkable efficiency. With an EPA-certified efficiency rating, these stoves are designed to maximize heat output while minimizing emissions. Users can enjoy a clean-burning fire that not only warms their space but also meets environmental standards. This efficiency is complemented by advanced technologies such as secondary combustion and catalytic converters, which enhance combustion processes and further reduce smoke and particulate emissions.

The RUVSOD models also come equipped with Vermont Casting's unique AirWash system. This innovative feature helps keep the glass door clean, allowing users to enjoy an unobstructed view of the flames. Additionally, the stoves in this series feature a customizable design, allowing consumers to choose from an array of colors and finishes that suit their interior decor. The stylish look of each stove adds a touch of elegance to any living space.

Another standout characteristic of the RUVSOD models is their user-friendly controls. An easy-to-use draft control system makes it simple to adjust the heat output and burn rate according to individual preferences. This ensures that users can maintain a comfortable and cozy atmosphere in their homes throughout the colder months.

In terms of heating capacity, these models can efficiently warm homes of various sizes, which makes them versatile for both small and large spaces. Their high heat output combined with long burn times ensures that users can enjoy hours of continuous heat without the need for frequent refueling.

In summary, the Vermont Casting RUVSOD series—models 3357, 3358, 3370, and 3379—represents the perfect blend of performance, style, and efficiency. With features such as advanced combustion technology, a customizable aesthetic, user-friendly controls, and impressive heating capabilities, these wood stoves stand as a premier choice for those looking to enhance their living space with an effective and attractive heating solution.
Top Page Image Contents