Troubleshooting/Fault Codes
FLASH | FAULT |
| ACTION | |
Pots/Pans | Normal Wash |
|
|
|
|
|
|
|
|
1 | 1 | Pan Flood Sensor Disconnect | Reset Unit and try again. If problem persists, contact service. | |
1 | 2 | Motor Control Status Error | Reset Unit and try again. If problem persists, contact service. | |
1 | 3 | Motor Control Comms Error | Reset Unit and try again. If problem persists, contact service. | |
1 | 4 | Diverter Timeout | Reset Unit and try again. If problem persists, contact service. | |
1 | 5 | Drain Error | 1. | Turn water on at sink and run garbage disposal to verify that sink is not clogged. |
|
|
| 2. | Verify that dishwasher drain hose is not clogged or kinked. |
|
|
| 3. | If draining into disposal, verify that plug has been removed from disposal. |
|
|
| 4. | Verify that drain hose has high loop, per installation guide. |
|
|
| 5. | Verify that dishwasher is level front to back and side to side. |
|
|
| 6. | Verify filters are not clogged. |
|
|
| Reset Unit and try again. If problem persists, contact service. | |
2 | 1 | Huba Disconnect Error | Reset Unit and try again. If problem persists, contact service. | |
2 | 2 | Fill Timeout | 1. | Verify water supply to dishwasher is turned on. |
|
|
| 2. | Verify that fill line is not kinked. |
|
|
| 3. | Verify that dishwasher is level front to back and side to side. |
|
|
| 4. | Turn water on at sink and verify there has not been a decrease in water pressure. |
|
|
| Reset Unit and try again. If problem persists, contact service. | |
|
|
|
|
|
2 | 3 | Low Level Sensor Error | 1. | Verify that no dishes have turned over and are holding a significant amount of water. |
|
|
| 2. | Verify that drain hose has high loop, per installation guide. |
|
|
| Reset Unit and try again. If problem persists, contact service. | |
2 | 4 | High Level Error | 1. | Verify items in rack are properly retained so that they can not turn over. |
|
|
| Reset Unit and try again. If problem persists, contact service. | |
|
|
|
|
|
2 | 5 | Level Sensor Error | 1. | Verify that dishwasher is level front to back and side to side. |
|
|
| 2. | Verify that drain hose has high loop, per installation guide. |
|
|
| Reset Unit and try again. If problem persists, contact service. | |
3 | 1 | Reset Unit and try again. If problem persists, contact service. | ||
|
|
|
| |
3 | 3 | Drain Pump Error | Reset Unit and try again. If problem persists, contact service. | |
3 | 4 | Motor Status | Reset Unit and try again. If problem persists, contact service. | |
|
|
|
| |
3 | 5 | Motor Under Voltage | Reset Unit and try again. If problem persists, contact service. | |
4 | 1 | Temperature Sensor Error | Reset Unit and try again. If problem persists, contact service. | |
|
|
|
| |
5 | 5 | Internal Error | Reset Unit and try again. If problem persists, contact service. | |
See Note A | Pan Flood | Reset Unit and try again. If problem persists, contact service. |
Product Care
Note A - Both lights flash continuously.
Note B - To reset unit, press and hold the START button 4 seconds.
Note C - Numbers listed indicate the times the lights will flash when a specific error is detected (example: For a drain error, the POTS/PANS light will flash once and the NORMAL WASH light will flash 5 times).
Note D - Cycle and Option keys will only illuminate after they are selected. To activate dishwasher, press START, the light will illuminate, close the door within 4 seconds and cycle will start.
Turning Audible Sound On and Off:
To turn off, press Rinse/Hold button for 10 seconds. The beep stops and the Rinse/Hold LED will flash 2 times. To turn on, repeat above instructions. The audible sound beeps 2 times and the Rinse/Hold LED flashes 2 times to identify that it is on.
Note: The audible sound cannot be disabled for error messages.
Note: The LED will flash in sync with the audible sound.
Product Care
36 | 37 |