To change security code:
1.Press and hold SETUP until it beeps.
2.Press SETUP briefly. The LCD will display "SC" (Security Code) and the current security code setting.
3.Use REPEATand SKlP to scroll to desired code, between 00 and 99.
4.Press SETUP to exit security code programming mode, and advance
to timelday- programming,. - - or.press STOP to exit.
SECURITY CODE
SElTlNG
g#jxi:
1
Bl %4
1
aor
To change the time display on the LCD:
1.Press and hold SETUP for 2 seconds or until it beeps.
2.Press SETUP 2 times until clock is displayed and the DAY icon is flashing.
3.Use REPEAT and SKlP keys to select correct day.
4.Press SETUP to advance to hour programming. Use REPEAT and SKlP keys to select correct hour and amlpm.
To change the number of mailboxes:
1.Press and hold SETUP for 2 seconds or until it beeps.
2.Press SETUP 5 times until MAILBOX icon is illuminated.
3.Use REPEAT and SKlP keys to scroll through selections (the Mailbox Number icons indicate which mailboxes are enabled).
4.Press SETUP to exit mailbox programming mode, and return to
ring type programming, or press STOP to exit.-
MAILBOX
PROGRAMMING
:%
4
~s
1
or
1
Announcement 2
You can record your own announcement butthecaller is notable to leave a message.
If you do not record your own announcement, the factory default announcement:
No one can answer the phone at the moment, please call again.
will be used (see Recording the Announcement ).
After you record your own announcement, you can return to the default announcement by record an OGM less than 1 second.
OGM (OutGoing Message)
You are not able to record an announcement, it is programmed into ITAD memory. The caller is not able to leave a message.
Programmed OGM Announcement: No one can answer the phone at the moment, please call again.
Note: The ITAD will default to OGM Announcement if the current
INote: , When accessing the ITADI remotely,the securitycode ispreceded by the * key.
Time and Day Setup
The Time and Daydefault is set to SUN 12:OO pm. This will flash to indicate clock has not been set.
5. Press SETUPto advanceto minute |
| Selecting the Announcement | |
programming. Use REPEAT and |
| ||
| The ANNC key is used to select the | ||
SKlP keys again. |
|
| |
|
| currentoutgoingannouncement.There | |
|
|
| |
6. Press SETUP to exit timelday |
| are 3 choices of Announcements as | |
| follows: 1, 2 & OGM. | ||
programming mode, and advance |
| ||
|
| ||
to mailbox programming, or press | 1 | Announcement 1 | |
STOP to exit. |
| ||
| YOUcan record your own personal | ||
Mailbox programming |
|
| announcementand the caller is able to |
|
| leave a message. | |
The ITAD has the ability to be |
| ||
| If you do not record your own | ||
programmed for up to | 4 individual |
| |
| announcement, the factory default | ||
|
|
| |
mailboxes. In addition, there is also a | announcement: | |
Generic mailboxfor general messages | ||
Please record message after the | ||
storage. On initial | ||
tone. | ||
Generic mailbox is enabled. | ||
will be used (see Recording the | ||
| ||
| Announcement). |
selection is Announcement 1 and the memory is full.
Recording the Announcement 1 . Press ANNC key until the desired announcement icon is displayed on the screen (1 or
2 ) .
2. Press and hold ANNC key for 2 seconds until a beep is heard. The clock will display 0:00 and will start incrementing for the length of the announcement.
