Watlow Electric 2000 - page 21

Application 2 Watlow MINICHEF 2000 ■ 19

light will be off.

With Sound set to 1, 2, or 3: [``end] will appear on the display and an audible tone

will be emitted. The Start/Stop key indicator light will flash rapidly. You can

acknowledge and silence the tone by pressing the Start/Stop key or it will automati-

cally time out within 2 seconds for setting 1 or 20 seconds for settings 2 or 3 and

then go into idle. The Start/Stop key indicator light will be off.

With sound set to 4 or 5: [``end]will appear on the display and the Start/Stop key

indicator light will flash rapidly.You must acknowledge the audible tone by pressing

the Start/Stop key.Once acknowledged the audible tone is silenced and the con-

troller goes into idle. The Start/Stop key indicator light will be off.

7. Once the controller goes into idle, the Start/Stop key indicator light and heat output

will switch off.The controller will not regulate to any temperature.

8. To repeat cooking,repeat steps 1 through 5 or 6.

Run a Menu (without preheat feature)

This procedure describes how to run an active menu when the preheat feature is inac-

tive - in other words, when the [ready] parameter in the [SetUp] function of the

Configuration Mode is set to [```no].

1. Select the menu you want to run as shown earlier in “Select a Menu”.

2. With idle on the display,place the food in the oven and insert the meat probe (if nec-

essary).

3. Press the Start/Stop key.

The Start/Stop key indicator will light up. Time will count down on the display.

The unit will run the following two-step cooking sequence:

Countdown time is displayed. It is the total of the programmed Time 1 plus Time 2.

Set point 1 and Fan 1 will run until Time 1 expires.

Set point 2 and Fan 2 will run until Time 2 expires.You will not see the switch-over

from Time 1 to Time 2.

4. When the timed cooking sequence is complete, the oven will run the probe cooking

sequence (if the probe parameter is set to [```on]) [Probe] will appear on the

display.

The unit will continue to cook until the food reaches the programmed probe temper-

ature.

5. Once the entire cooking sequnce (timed cook and probed cooking) is complete, the

unit will switch to the Hold sequence. The display will alternate slowly between

H

MINICHEF 2000

[probe]

Edit Accept

Back-UpExit

AB

DE

C

F

G

DE

C

F

MINICHEF 2000

[ready]

Edit Accept

Back-UpExit

DE

C

F

MINICHEF 2000

[`1459]

Edit Accept

Back-UpExit

AB

GH

AB

GH

STEADY

ON

RAPID

FLASH

Contents

Main MINICHEFTM 2000 Applications 1 - 6 Cook-&-Hold Oven Applications Guide Watlow Controls Programming & Operating Steps ISO 9001 TOTAL Table of Contents Application 1 Oven with Meat Probe Option 2 Watlow MINICHEF 2000 Application 1 Note: For details, see wiring instructions in the Input 2 Probe Temperature Event Input 1 Door Event Input 2 not used Application 1 Watlow MINICHEF 2000 3 this application. You must select Application 1 to access them. For directions, see the Page Step 7 Design a Faceplate Overlay Step 8 Operate the Controller Startup Page Page Page Cancel a Menu Temperature Alarms Errors Application 2 Oven with Meat Probe Option 12 Watlow MINICHEF 2000 Application 2 Note: For details, see wiring instructions in the Down Input 2 Probe Temperature Event Input 1 Door Open Event Input 2 not used Start/ Stop Up 4 Menu Select Application 2 Watlow MINICHEF 2000 13 this application. You must select Application 2 to access them. For directions, see the Page Page Select a Menu Application 2 Watlow MINICHEF 2000 17 [pre-`] [`Heat] [`1459] STEADY ON [`idle] Page Page Restart a Menu Change Menus Temperature Alarms Page Application 3 Oven Note: For details, see wiring instructions in the 24 Watlow MINICHEF 2000 Application 3 Application 3 Watlow MINICHEF 2000 25 this application. You must select Application 3 to access them. For directions, see the Page Page Startup Page Page Page Page Application 4 Automatic Cook-&-Hold Oven 34 Watlow MINICHEF 2000 Application 4 Note: For details, see wiring instructions in the Down Input 2 not used Event Input 1 Door Open Event Input 2 not used Event Output 1 Fan Low Start/ Stop Up 4 Menu Select Application 4 Watlow MINICHEF 2000 35 this application. You must select Application 4 to access them. For directions, see the Page Page Select a Menu Page Page Page Page Application 5 Manual Cook-&-Hold Oven with Meat Probe Option 44 Watlow MINICHEF 2000 Application 5 Note: For details, see wiring instructions in the Up Down 1 Temp(s) 2 Application 5 Watlow MINICHEF 2000 45 this application. You must select Application 5 to access them. For directions, see the Page M Set the Menu Single Step Menu Set the cooking time: Set the Hold Temperature Five Second Timeout Two Step Menu Set the two cooking temperatures and one probe temperature Set the two cooking times Set the Hold Temperature Five Second Timeout Run a Menu (with no preheat feature) View Actual Oven Temperature Adjust a Menu While Cooking Pause a Menu Restart a Menu Change Menus Temperature Alarms Application 6 Manual Cook & Hold Oven 56 Watlow MINICHEF 2000 Application 6 Note: For details, see wiring instructions in the Up Down 1 Temp(s) 2 Application 6 Watlow MINICHEF 2000 57 this application. You must select Application 6 to access them. For directions, see the of all parameters and values Page M Set the Menu Single Step Menu Two Step Menu Page Page View Actual Oven Temperature Adjust a Menu While Cooking Pause a Menu Change Menu or Restart Temperature Alarms Specifications 66 Watlow MINICHEF 2000 Specifications Ordering Information Ordering Information Watlow MINICHEF 2000 67 68 Watlow MINICHEF 2000 Ordering Information MINICHEF 2000 Accessories Tool Ordering Information: Part Numbers & Accessories MINICHEF 2000 Documentation Watlow Controls Page Application 6 Watlow MINICHEF 2000 71 Ordering Information