Watlow Electric 2000 - page 65

Application 6 Watlow MINICHEF 2000 ■ 63

• The heat output indicator light - G, just below the display- will light up whenever

the controller is calling for heat.

When the oven is at operating temperature (above the relative set point minus the

ready band) [ready] will appear on the display and the Start/Stop key indicator

light will flash rapidly.You are now ready to cook with the active menu.

If the oven is at operating temperature, the display goes directly to [ready] with-

out indicating preheat or temperature.

Note: You can skip preheat and go directly to the cooking sequence by pressing the Start/Stop key a second time.

Run a Menu (with preheat feature)

This procedure describes how to run an active menu when the preheat feature is active

(when the [ready] parameter in the [setUp] function of the Configuration mode is set

to [``yes]).

1. Set the menu as shown earlier.

2. With [`idle] or time of day on the display,press the Start/Stop key.

If the preheat condition has not been met, the oven will preheat until [ready]

appears on the display.

Note: You can skip preheat and go directly to the cooking sequence by pressing the Start/Stop key a second time.

If the oven is already at operating temperature [ready] will appear on the display.

3. With [ready] on the display,place the food in the oven Then press the Start/Stop

key (indicated by the rapidly flashing indicator light).

The Start/Stop key indicator will light up. Time will count down on the display.

Depending on the way the controller was programmed at [Etype] / [Steps] the

menu will run in one step or two.

One Step

Countdown time is displayed.

Set point 1 will run until time expires.

Two Step

Countdown time is displayed. It is the total of the programmed Time 1 plus Time 2.

Set point 1 will run until Time 1 expires.

Set point 2 will run until Time 2 expires.You will not see the switch-over from Time

1 to Time 2.

4. When the cooking sequence is complete,the unit will switch to the Hold sequence.

An audible tone will sound for two seconds.

The display will alternate slowly between [`HoLd] and count up time.

AB

DE

C

F

GH

MINICHEF 2000

[`idle]

Edit Accept

Back-UpExit

SLOW

FLASH

AT OPERATING TEMPERATURE

(PREHEAT CONDITION MET)

RAPID

FLASH

B

DE

C

F

MINICHEF 2000

[100f`]

Edit Accept

Back-UpExit

B

DE

C

F

MINICHEF 2000

[ready]

Edit Accept

Back-UpExit

G H GH

A A

[pre-`] [`Heat]

Contents

Main MINICHEFTM 2000 Applications 1 - 6 Cook-&-Hold Oven Applications Guide Watlow Controls Programming & Operating Steps ISO 9001 TOTAL Table of Contents Application 1 Oven with Meat Probe Option 2 Watlow MINICHEF 2000 Application 1 Note: For details, see wiring instructions in the Input 2 Probe Temperature Event Input 1 Door Event Input 2 not used Application 1 Watlow MINICHEF 2000 3 this application. You must select Application 1 to access them. For directions, see the Page Step 7 Design a Faceplate Overlay Step 8 Operate the Controller Startup Page Page Page Cancel a Menu Temperature Alarms Errors Application 2 Oven with Meat Probe Option 12 Watlow MINICHEF 2000 Application 2 Note: For details, see wiring instructions in the Down Input 2 Probe Temperature Event Input 1 Door Open Event Input 2 not used Start/ Stop Up 4 Menu Select Application 2 Watlow MINICHEF 2000 13 this application. You must select Application 2 to access them. For directions, see the Page Page Select a Menu Application 2 Watlow MINICHEF 2000 17 [pre-`] [`Heat] [`1459] STEADY ON [`idle] Page Page Restart a Menu Change Menus Temperature Alarms Page Application 3 Oven Note: For details, see wiring instructions in the 24 Watlow MINICHEF 2000 Application 3 Application 3 Watlow MINICHEF 2000 25 this application. You must select Application 3 to access them. For directions, see the Page Page Startup Page Page Page Page Application 4 Automatic Cook-&-Hold Oven 34 Watlow MINICHEF 2000 Application 4 Note: For details, see wiring instructions in the Down Input 2 not used Event Input 1 Door Open Event Input 2 not used Event Output 1 Fan Low Start/ Stop Up 4 Menu Select Application 4 Watlow MINICHEF 2000 35 this application. You must select Application 4 to access them. For directions, see the Page Page Select a Menu Page Page Page Page Application 5 Manual Cook-&-Hold Oven with Meat Probe Option 44 Watlow MINICHEF 2000 Application 5 Note: For details, see wiring instructions in the Up Down 1 Temp(s) 2 Application 5 Watlow MINICHEF 2000 45 this application. You must select Application 5 to access them. For directions, see the Page M Set the Menu Single Step Menu Set the cooking time: Set the Hold Temperature Five Second Timeout Two Step Menu Set the two cooking temperatures and one probe temperature Set the two cooking times Set the Hold Temperature Five Second Timeout Run a Menu (with no preheat feature) View Actual Oven Temperature Adjust a Menu While Cooking Pause a Menu Restart a Menu Change Menus Temperature Alarms Application 6 Manual Cook & Hold Oven 56 Watlow MINICHEF 2000 Application 6 Note: For details, see wiring instructions in the Up Down 1 Temp(s) 2 Application 6 Watlow MINICHEF 2000 57 this application. You must select Application 6 to access them. For directions, see the of all parameters and values Page M Set the Menu Single Step Menu Two Step Menu Page Page View Actual Oven Temperature Adjust a Menu While Cooking Pause a Menu Change Menu or Restart Temperature Alarms Specifications 66 Watlow MINICHEF 2000 Specifications Ordering Information Ordering Information Watlow MINICHEF 2000 67 68 Watlow MINICHEF 2000 Ordering Information MINICHEF 2000 Accessories Tool Ordering Information: Part Numbers & Accessories MINICHEF 2000 Documentation Watlow Controls Page Application 6 Watlow MINICHEF 2000 71 Ordering Information