Manuals / Weider / Fitness & Sports / Home Gym

Weider 831.153931 user manual Bags, check to see if it has been pre-assembled

Models: 831.153931

1 35

Download 35 pages 1.95 Kb

Page 29

This chart		is provided to help you identify the small parts used in assembly. The number in parenthesis below
each	part refers to the key number of the part from the PART LIST in the center of this manual.		Important:
Some	parts	may have been pre-assembled for shipping purposes. If you cannot find a part in the parts

bags, check to see if it has been pre-assembled.

Note: Assembly is divided into four stages: 1) frame assembly, 2) arm assembly, 3) cable assembly, and 4) seat assembly. The hardware for each stage is packaged in separate bags. WAIT UNTIL YOU BEGIN EACH ASSEMBLY STAGE TO OPEN THE PARTS BAG LABELED FOR THAT ASSEMBLY STAGE.

Image 29

Weider 831.153931 user manual Bags, check to see if it has been pre-assembled

Contents

Patent Pending Model No Serial NoSerial Number Decal under seat Table of Contents Weight system in the location shown Important PrecautionsSure that the cables are on all of the pulleys DecalBefore YOU Begin Using the weight systemAssembly Them in place Do not tighten the Nylon Locknuts yet Each Carriage Bolt. Do not tighten the Nylon Locknuts yetNylon Locknuts Two indicated 5/16 x 2 1/2 Carriage Bolts 110 Hole in the Swivel Upright AdjustmentLocknut 86 onto each Carriage Bolt En the Nylon Locknuts yetGrooved side is facing downward Make sureDo not tighten the Locknuts yet Must be able to pivot easily. R With the Bolt and a 3/8 Nylon Jamnut8 Nylon Jamnut 113 as shown EasilyLong and has an eyelet on each end Bolt 100 and a 3/8 Nylon Locknut Cable in the groove of the PulleyGroove of the Pulley Attach the end of the Swivel Cable 17 toPulley A 3/8 Nylon JamnutLocate the Butterfly Cable 69, which is Locknut 87. Make sure that the Long CableEd pin on the other end Locate the Leg Lever Cable 75, which isWasher 91, and a 3/8 Nylon Jamnut Upright 3 with a 3/8 x 3 3/4 Bolt 122, a 3/8End and a ball on the other end A 3/8 Nylon Locknut 119 122 121 113 Cage 120A 3/8 Nylon Locknut 120 With a 3/8 x 2 Bolt 100 and a 3/8 NylonNylon Locknut 120 OnlyA 3/8 Nylon Jamnut 124Nut 118 halfway onto the end A 3/8 Nylon LocknutNut against the 1/2 Washer 1. Rem Stack. Replace the PinTighten all of the 3/8 Nylon Locknuts 87 used in this step Repeat this step with the other end of the Squat ArmNylon Locknuts yet Backrest than the top. Attach the Squat Backrest to Ing any exercise AdjustmentsPress 115 Adjusting the Squat ARM or Swivel CarriageLbs Top Weight Resistance ChartPulley and the Cable Trap between the higher set TroubleshootingSwivel High Cable Cable DiagramsButterfly Swivel Low Leg LeverCable Full 90 DAY Warranty Bags, check to see if it has been pre-assembled X 3 3/4 Bolt R1202APage Round Inner Cap 2 x 2 Inner Cap 2 1/2 Inner Cap Save this Part LIST/EXPLODED Drawing for Future Reference Key Qty Description Part LIST-Model NoExploded