Weider 831.159833 user manual Identify the Ab Cable 74. It is approximately

Models: 831.159833

1 37
Download 37 pages 27.72 Kb
Page 15
Image 15

29. Wrap the Rear Cable (70) under a 90mm Pulley

29

 

 

 

 

(35). Attach the Pulley and a Cable Trap (38) to

 

 

 

 

 

 

 

 

 

the top hole in the pair of Pulley Plates (32) with

 

 

 

 

 

an M10 x 48mm Bolt (93) and an M10 Nylon

 

 

 

 

 

Locknut (90). Make sure the Cable Trap is posi-

 

 

 

 

 

tioned to hold the Cable in the groove of the

 

 

 

 

 

Pulley.

 

 

 

 

 

 

 

70

 

93

 

 

 

 

 

 

 

90

 

35

32

 

 

 

 

 

 

 

 

 

 

 

32

38

 

 

 

 

 

 

30. Wrap the Rear Cable (70) over a 115mm Pulley

30

 

 

 

 

(36) in the direction shown. Attach the Pulley

 

 

 

 

Bracket

90

 

 

inside the indicated bracket on the Center Top

 

 

 

 

 

Frame (8) with an M10 x 45mm Bolt (94) and an

 

 

 

 

36

M10 Nylon Locknut (90).

 

 

 

 

 

 

 

 

94

 

 

 

 

 

 

 

8

 

 

 

 

 

 

 

70

 

31. Attach the end of the Rear Cable (70) to a “U”-

31

 

 

 

 

bracket (33) with an M8 Washer (100) and an M8

 

 

 

 

 

 

 

 

 

Nylon Locknut (86). Do not completely tighten

 

 

 

 

 

the Locknut; it should be tightened so that

 

 

 

 

 

only two threads of the Cable show past the

 

70

 

 

 

Locknut, as shown in the inset drawing.

 

96

 

 

 

 

 

 

Attach the “U”-bracket (33) to the Short Weight

33

 

100

 

70

Tube (44) with an M8 x 45mm Bolt (96) and an

86

 

 

M8 Nylon Locknut (86).

 

 

86

 

33

 

 

44

 

 

 

 

 

 

 

 

 

 

86

32. Identify the Ab Cable (74). It is approximately

32

 

 

 

 

226 1/2” long, and it has a ball on one end and

 

 

 

 

 

 

 

 

 

an eyelet on the other.

 

 

 

Large tabs

 

90

97

 

Wrap the Ab Cable (74) over a 90mm Pulley (35)

 

on this side

 

 

39

 

as shown. Place two Pulley Covers (39) over the

 

 

 

 

 

 

 

 

Pulley, so that the large tabs are on the indicated

 

Pin

 

 

39

side. Attach the Pulley and Pulley Covers to the

 

 

 

 

Butterfly Upright (4) with an M10 x 97mm Bolt

 

4

 

 

77

(77), two M10 Washers (97), and an M10 Nylon

 

35

 

97

Locknut (90). Make sure the Cable is between

 

 

74

 

 

 

 

the Pulley and the pin on the Upright.

 

 

 

 

 

 

 

 

 

15

Page 15
Image 15
Weider 831.159833 user manual Identify the Ab Cable 74. It is approximately