22. Identify the Right and Left Butterfly Arms (19, 20) | 22 | Bracket | 7 |
|
by the positions of the welded brackets. |
| |||
|
|
|
| |
Press a 45mm Square Inner Cap (68) into each |
| Lubricate |
|
|
end of the Right Butterfly Arm (19). Wet the lower |
| Axles |
|
|
|
|
|
| |
end of the Butterfly Arm with soapy water. Slide a |
|
|
| Welded |
Large Foam Pad (53) onto the lower end of the |
|
|
| Brackets |
Butterfly Arm. |
|
|
|
|
Lubricate the axles on the Butterfly Top Frame (7) |
|
| 68 |
|
with grease. Orient the Right Butterfly Arm (19) |
| 19 | 54 |
|
as shown and slide it onto the right axle. |
|
|
| |
|
|
|
| |
See the inset drawing. Place two 25mm |
|
| 55 |
|
Retainers (54) on top of an inverted 25mm Cover |
|
| 20 |
|
Cap (55). Make sure the teeth on the Retainers |
|
|
| |
|
|
|
| |
bend toward the Cover Cap, as shown. |
| 53 |
|
|
|
|
|
| |
Have a second person gently tap the two 25mm |
|
|
|
|
Retainers (54) and the 25mm Cover Cap (55) |
| 68 |
|
|
onto the axle on the Butterfly Top Frame (7). |
|
|
| |
|
| Axle | ||
|
|
| ||
Repeat this step with the Left Butterfly Arm |
|
|
|
|
(20). |
|
| 54 |
|
|
|
|
| |
|
|
| Teeth |
|
Cable Assembly |
|
|
| 55 |
|
|
|
| |
23. Locate and open the parts bag labeled | 23 |
|
|
|
“CABLE ASSEMBLY.” |
|
|
|
|
For cable identification and routing during |
|
|
|
|
steps 23 to 61, refer to the CABLE DIAGRAMS |
|
|
| 86 |
and CABLE ID CHART on pages 30 and 31. |
|
|
| |
Make sure that the cable traps do not touch or |
|
|
| Bracket |
bind the cables as you assemble them. |
|
| 20 |
|
|
|
|
| |
Identify the Butterfly Cable (73). It is approxi- |
|
|
| 73 |
mately 52” long and it has an eyelet on each end. |
|
|
| |
|
|
| 84 | |
Attach the Butterfly Cable to the bracket on the |
| Flat |
| |
Left Butterfly Arm (20) with an M8 x 20mm |
|
|
| |
Shoulder Bolt (84) and an M8 Nylon Locknut (86). |
| Side |
|
|
|
|
|
| |
Make sure that the flat side of the eyelet on | 24 |
|
|
|
the cable (see the inset drawing) is against |
| 37 |
| |
|
|
| ||
theButterfly Arm. |
|
|
| |
|
|
|
| |
24. Locate and open the parts bag labeled |
|
|
| 34 |
|
|
|
| |
“PULLEY BAG 2.” Remove one |
|
|
|
|
from the bag. |
|
|
|
|
|
|
| 90 |
|
Wrap the Butterfly Cable (73) over the |
|
| 73 | 114 |
(34). Attach the |
| 4 |
|
|
(37) to the bracket on the back of the Butterfly |
|
|
| |
|
|
|
| |
Upright (4) with an M10 x 58mm Bolt (114) and |
|
|
|
|
an M10 Nylon Locknut (90). Make sure the Long |
|
|
|
|
Cable Trap is oriented to hold the Cable in the |
|
|
|
|
groove of the |
|
|
|
|
13
