Manuals / Whirlpool / Kitchen Appliance / Range

Whirlpool RF386PXD PROBLEM Cooking results are not what you expected, The display is showing “PF”

Models: RF386PXD

1 51

Download 51 pages 55.32 Kb

Page 48

PROBLEM

PROBLEM

Cooking results are not what you expected

The display is showing “PF”

“F” followed by a number shows on the display

CAUSE

@The range is not level. (See Installation Instructions.)

.The oven temperature seems too low or too high. See “Adjusting the’oven temperature control” on page 18 to adjust oven temperature.

.You did not preheat the oven before baking (if called for in recipe).

l The recipe you are using may need to be altered to improve the taste or appearance of the food.

l \iou are using a pan that is not the correct type or size. Refer to a reliable cookbook or recipe for recommended pan type and size.

l There is not enough air space around pan when baking. Allow 1M to 2 inches (4-5 cm) of air space on all sides of pan. There must be a minimum space of 1 inch.

l The cooking utensil is too large or too small for the surface unit being used. Pan should be the same size or slightly larger than the surface unit being used.

l There has been a power failure. Reset the clock. (See page 13.)

l The electronic control or temperature sensor has failed. Call for service. (See Step 2 on page 49.)

If none of these items was causing your problem, see “Requesting Assistance or Service” on page 49.

48

Image 48

Whirlpool RF386PXD warranty PROBLEM Cooking results are not what you expected, The display is showing “PF”, Cause

Contents

SELF-CLEANINGELECTRIC RANGE MODEL RF386PXDUseAndCare Contents A Note to You Thank you for buying a WHIRLPOOL@ appliancePlease record your model’s information Our Consumer AssistanceRange Safety IMPORTANT SAFETY INSTRUCTIONS‘\ 4s When using the oven Getting to Know Your Range Control panelUsing Your Range Using the surface unitsSurface unit indicator lights Hot swface indicator lightsUsing the ceramic glass cooktop Cookware tipsRack placement for specific foods i~~~“-eunit l Positioning racks andUsing aluminum foil for baking For best air circulationCommand pads Using the control lockThe electronic oven control Display/clockSetting the clock 1. Press Clock padtime clockUsing the electronic Minute Timer 1. Press Timer Set padStart Minute Timer Minute TimerCanceling a function Audible signalsTo cancel the Minute Timer Press Timer Off pad3. Set temperature 2.Choose baking/roasting settingBaking/roasting 1. Position7. After cooking, turn off oven Adjusting the oven temperature control 2. Set new offset temperature3. Enter the adjustment To display temperatures in “C instead of “FHow to determine the amount of adjustment needed Broiling1. Position rack 3.Position door6. When broiling is done, turn off To custom broil at a lower temperature5. Start oven ovenBroiling rack position chart Broiling tipsUsing the electronic MEALTIMER” control Energy saving tipsMethod l-UsingCook Time 1. Prepare oven 2. Choose Bake setting3. Set temperature optional.PRESS YOU SEE 4. Press Cook Time pad7. When baking/roasting Method 2-UsingStop Time 1. Prepare oven6. Start oven is done3. Set temperature optional 4. Press Stop Time pad5. Set stop time 2. Choose Bake setting7. When baking/roasting Press Delay Start Time pad 9. When start time is reachedSet cook time Set start10. When baking/roasting is done Method 2-UsingDelay Start Time and Stop Time4. Press Delay Start Time pad 11. Turn off oven5. Set start 6. Press Stop Time padSet stop CompleteMethod 3-UsingCook Time and Stop Time 9. When start time is reached10. When baking/roasting is done 2. Choose Bake setting4.Press Cook Time pad 5.Set cook time 7. Set stop time3. Set temperature optional 6. Press Stop Time pad9.When start time is reached 8. Complete entry10. When baking/roasting is done 11. Turn off ovenThe oven vent The storage drawerThe anti-tipbracket Optional door panel patUsing the Self-CleaningCycle Before you startBefore setting the controls Setting the controls4. After Self-Cleaningcycle starts 5. After Self-Cleaning6. When oven reaches normal temperaturescleaning 2. Settime optional 3. Press Stop Time pad6. After Self-Cleaningcycle starts 7. After Self-Cleaningcycle ends8. When oven reaches normal baking/roasting temperaturesTo delay start using delay To stop the Self-Cleaningcycle at any time 6. After Self-Cleaningcycle starts7. After Self-Cleaningcycle ends 8. When oven reaches normalSpecial tips How the cycle worksCleaning the cooktop Caring for Your RangeCleaning tips Cleaning otherparts rangeThe oven light Troubleshooting problems and their causesIf nothing operates, check the following Other possiblePROBLEM Cooking results are not what you expected The display is showing “PF”“F” followed by a number shows on the display CAUSERequesting Assistance or Service 2. If you need service3.If you need FSP@ replacement parts 1. If you need assistanceIndex WHIRLPOOL@ CLEANTOP” Freestanding Range Warranty