• Press

−

Down to display the number of regenerations initiated by this electronic

control since the LE code number was entered.

6.Press and hold the PROGRAM button until LE31 shows in the display.

This code identifies the softener model. If the wrong number shows, the softener will operate on incorrect programming.

7.Return the present time display — Press the PROGRAM button.

8. To change LE number — Press the + Up or

−

Down button until the correct code shows.

Then, press the

PROGRAM button to return to the present time display.

Manual Advance Regeneration Check --- Model WHES30

This check verifies proper operation of the valve motor, brine tank fill, brine draw, regeneration flow rates, and other controller functions. Always make the initial checks, and the manual initiated diagnostics.

NOTE: The electronic control display must show a steady time (not flashing). If an error code shows, first press the PROGRAM button to enter the diagnostic display.

1.Press the RECHARGE button and hold in for 3 seconds. RECHARGE begins to flash as the softener enters the fill cycle of regeneration. Remove the brinewell cover and, using a flashlight, observe fill water entering the tank.

If water does not enter the tank, look for an obstructed nozzle, venturi, fill flow plug, brine tubing, or brine valve riser pipe.

2.After observing fill, press the RECHARGE button to move the softener into brining. A slow flow of water to the drain will begin. Verify brine draw from the brine tank by shining a flashlight into the brinewell and observing a noticeable drop in the liquid level. This may take 15 to 20 minutes to notice.

NOTE: Be sure water is in contact with the salt, and not separated by a salt bridge... see “Breaking A Salt Bridge” section.

If the water softener does not draw brine, check for (most likely to least likely)

•Dirty or plugged nozzle and venturi, see “Cleaning the Nozzle and Venturi” section

•Nozzle and venturi not seated on the gasket, or gasket deformed

•Restriction in valve drain, causing a back-pressure (bends, kinks, elevated too high, etc.), see “Install Valve Drain Hose” section

•Obstruction in brine valve or brine tubing

•Inner valve failure (obstructed outlet disc, wave washer deformed, etc.)

NOTE: If water system pressure is low, an elevated drain hose may cause back pressure, stopping brine draw.

3.Again, press the RECHARGE button to move the softener into backwash. Look for a fast flow of water from the drain hose.

An obstructed flow indicates a plugged top distributor, backwash flow plug, or drain hose.

33

Page 32 Page 34
Page 33
Image 33
Whirlpool WHES20 manual Manual Advance Regeneration Check --- Model WHES30
Page 32 Page 34

WHES30, WHES20 specifications

The Whirlpool WHES30 and WHES20 are innovative water softeners designed to enhance the quality of your home’s water supply. These models are engineered to effectively reduce hard water minerals such as calcium and magnesium, providing soft water that helps protect your plumbing and appliances from scale buildup while improving the efficiency of soap and detergent.

One of the standout features of the WHES30 and WHES20 is their capacity. The WHES30 has a higher capacity, making it suitable for larger households requiring consistent soft water for daily use. It can handle water hardness levels of up to 120 grains per gallon and is designed to accommodate up to 30,000 grains of hardness removal, ensuring that even in high-demand scenarios, families can rely on a consistent supply of softened water. In contrast, the WHES20 is ideal for smaller households or those with milder water hardness issues, capable of managing up to 20,000 grains.

Both models utilize a demand-initiated regeneration process, which is an energy-efficient technology that allows the systems to regenerate only when necessary. This not only saves water and salt but also extends the lifespan of the system. The softeners use a high-efficiency brining cycle, which reduces waste and enhances performance, ensuring that you have soft water available at all times.

The Whirlpool WHES series also features easy-to-use digital controls. This user-friendly interface enables homeowners to easily monitor and program the system settings according to their specific needs. Detailed diagnostic information is displayed, allowing users to track water usage and maintenance schedules efficiently.

Additionally, both water softeners come equipped with a two-in-one system design that incorporates a built-in brine tank, simplifying installation and saving valuable space in your home. The compact nature of these models ensures they can fit into various locations without taking up excessive room.

In terms of construction, the WHES30 and WHES20 are durable and designed for longevity. They are built with sturdy materials that resist corrosion and ensure reliable performance over the years. This commitment to quality makes these water softeners a valuable investment for any household.

Overall, the Whirlpool WHES30 and WHES20 models deliver user-friendly operation, efficient performance, and high-quality components, making them excellent choices for anyone looking to improve their water quality through effective softening technology.
Top Page Image Contents