Machine Troubleshooting, Excessive dusting | Windsor QTFSG, QTFSD

MACHINE TROUBLESHOOTING

PROBLEM.	CAUSE	SOLUTION

Excessive dusting	Dust skirts and seals worn,	Replace or adjust skirts or seals.
	damaged, not adjusted
	properly
	Dust filter clogged or	Shake and clean or replace filter.
	damaged
	Vacuum hose damaged	Replace vacuum hose.
	Vacuum fan not operated	Belt loose, broken or off pulley.
Poor sweeping	Broom bristles worn	Replace brooms.
performance
	Brooms not adjusted	Adjust brooms.
	properly.
	Debris caught in broom	Free mechanism of debris.
	drive mechanism.
	Main broom drive failure	Belt loose, broken or off pulley.
	Side broom drive failure	Check circuit breaker. Check side broom motor
		circuit.
	Hopper dump door closed	Open dump door.
	Hopper full	Empty hopper.
	Hopper floor skirts worn,	Replace skirts.
	damaged
Machine travels slowly	Parking brake set	Release parking brake.
or not at all
	Towing valve activated.	Release towing valve.
	Linkage broken or not	Inspect and adjust or repair.
	properly adjusted
	Transmission drive belt	Inspect and repair.
	slipping or broken
	Main engine drive belt	Inspect and repair.
	failure
	Differential drive chain	Inspect and repair.
	failure.

4-17	QTFSG/QTFSD 98349 05/15/03

Image 34

Windsor QTFSG, QTFSD manual Machine Troubleshooting, Excessive dusting, Poor sweeping, Machine travels slowly, Or not at all

Contents

Floor Sweeper Model Tracer FS Your Dealer Machine Data LOGOverview Table of Contents HOW to USE this Manual Model Important Safety Instructions Read ALL Instructions Before Using this Machine Hazard Intensity Level Hazard Intensity Level Safety Label Location Safety Label Location Technical Specifications DIMENSION/CAPACITY Controls Special Notes Controls Brake Pedal Filter Shaker SwitchDirectional Control Pedal Parking Brake Lever Hopper Safety ARM Hopper Door SwitchHopper Lift Switch Engine Temperature Light Circuit Breakers KEY SwitchChoke GAS only Horn PAD Starting the Machine OperationsBefore Operating the FS To Sweep Storing the Machine To Engage the Hopper Safety ARMStopping the Machine Dumping the Hopper Machine Jacking To Disengage the Hopper Safety ARMTowing or Pushing Machine To Jack UP Machine Hydraulic Fluid Reservoir MaintenanceHydraulic Fluid Hydraulic Pump Directional Control System Hydraulic FilterRefer to the Electrical Control Group in the Parts section To Install the Main Broom To Remove the Main Broom Main Broom Adjustment Knob Checking and Adjusting the Main Broom PatternMain Broom Pattern To 1-1/2 25.4 to 38.1mm Raised hopper may fall. Engage hopper safety arm To Install the Side BroomAdjusting the Side Broom To Remove the Side Broom To Replace Belt Adjusting the Jackshaft BeltTransmission Jackshaft Belt Transmission Belt Replacing and Adjusting the Vacuum Impeller Belt Replacing and Adjusting Main Broom BeltTo Align Belt To Realign Replacing and Adjusting DifferentialImpeller Belt Drive Chain Adjusting the Right Broom Door Skirt Replacing and Adjusting the Drive Wheel ChainsReplacing the Right Broom Door Skirt Replacing the Left Broom Skirt Adjusting the Left Broom SkirtAdjusting the Rear Broom Skirt Recirculation Skirt Replacing the Hopper Seals Adjusting the Hopper Side SealsHopper Seals Hopper LIP Skirts Hopper Hopper Door SealsReplacing Door Seals Hopper Dust Filter AIR To Adjust the BrakesRaised hopper arm may fall. Engage hopper safety arm Brakes Refer to the Brake Group in the Parts section Battery Battery Maintenance Hopper will not lift Hydraulic Schematic Hydraulic TroubleshootingProblem Cause Solution Hopper will not lower Pressing foot pedal No propellingMachine moves without Full speed only Poor sweeping Machine TroubleshootingExcessive dusting Machine travels slowly Service Schedule Maintenance Daily Weekly 50HRS