Manuals / Woods Equipment / Lawn and Garden / Chipper

Woods Equipment 8000, 8100 manual GreaseableBearings

Models: 8100 8000

1 40

Download 40 pages 29.25 Kb

Page 20

S E R V I C E A N D M A I N T E N A N C E

Important!

Check the bolts on the following for correct torque (75 ft. lbs.) every

10 hours of operation:

•Hydraulic feed roller bearing

•Hydraulic motor mounting

•Chipper rotor bearing

•Chipper blades

•Rotor paddles

•Chipper anvil

Warning: Failure to maintain proper fastening torque (75 ft. lbs.) on bolts for the components listed above may result in severe damage to the chipper and/or personal injury!

GreaseableBearings

The PTO model has ten grease zerks. Minimal periodic greasing is needed on these points every 50 hours:

•Four grease zerks on the PTO shaft itself.

•Two greaseable bearings on the rotor shaft.

•Two greaseable bearings on the bottom jack shaft.

•One idler arm pivot

•One discharge chute

PN-51210 (Rev. 7/98)

18

Image 20

Woods Equipment 8000, 8100 manual GreaseableBearings

Contents

INCLUDES SERVICE INFORMATION operators manualMODEL 8000 CHIPPERBealert!YourSafetyisInvolved DearWoodsCustomerOwners Record Model Number Serial Number DatePurchasedContents Safety Instructions DANGEREmpty the cutting chamber before starting the machine Additional Safety Rules for PTO Models Stay alert and pay attention when PTO chipper is operatingKeep bystanders, especially children, away from the PTO driveline Check the driveline to ensure it is attached securely to the tractorSafeStorage SafetyDecals Assembly TorqueChartAttach Chipper Chute Figure1Page Figure4 Connect the Hydrostatic Control CableConnect PTO Shaft PTOModel Controls Figure5 Telescoping Type 20 to 28 inches will leave at least 4 inches overlap OperationStarting Chipping Stopping ServiceandMaintenanceSchedule Inspection ItemsFigure8 ServiceandMaintenanceSharpeningChipperBlades Chipping Blade Sharpening Tips SettingChippingBladeClearanceTo Adjust Adjusting or Replacing Drive Belts Clearing Plugged RotorRepairing or Replacing Rotor Bearings GreaseableBearings Installing the Optional Hydraulic Feed KitFor models without factory HydraulicFeedInstall the 6.6 Pulley Mount the Hydrostatic PumpConnect the Hydrostatic Cable Figure9Attach the Valve and Mount the Reservoir Connect the BeltHydraulic Feed Operating Instructions Hydrostatic Pump Start Up ProcedureFluids Figure10 Pump-Component LocationsFigure11 HydraulicSchematicControlArmOperation HydraulicFeedMaintenance HydrostaticPumpTroubleshootingSymptom Probable CauseTroubleshooting ProblemProbable Cause SuggestedChute and Rotor Assembly Part List Service AccessoriesPart# DescriptionC H U T E A N D R O T O R A S S E M B L Y D I A G R A M ChuteandRotorAssemblyDiagramPN-51210 Rev. 7/98 ChipperBaseAssemblyDiagram Chipper Base Parts List Spacer, RHBearing, 2 BLT FLG 1-1/2 Bore Bushing SK1.5Description H Y D R A U L I C F E E D A S S E M B L Y D I A G R A M HydraulicFeedAssemblyDiagramPN-51210 Rev. 7/98 PN-51210 Rev. 7/98 H Y D R A U L I C F E E D A S S E M B L Y D I A G R A MHydraulic Feed Parts List Specifications Specifications are subject to change because of design modificationsPage Page Page Warranty WarrantyHEALTHWARNING