SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Do not operate or transport equipment while under the influence of alcohol or drugs.

Operate only in daylight or good artificial light.

Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of all moving parts.

Always comply with all state and local lighting and marking requirements.

Never allow riders on power unit or attachment.

Power unit must be equipped with ROPS or ROPS cab and seat belt. Keep seat belt securely fastened. Falling off power unit can result in death from being run over or crushed. Keep foldable ROPS system in “locked up” position at all times.

Always sit in power unit seat when operating controls or starting engine. Securely fasten seat belt, place transmission in neutral, engage brake, and ensure all other controls are disengaged before starting power unit engine.

Operate tractor PTO at 540 RPM (1000 RPM on Q Series cutters). Do not exceed.

Raise or lower wings slowly to prevent personal injury or damage to cutter.

Connect PTO driveline directly to power unit PTO shaft. Never use adapter sleeves or adapter shafts. Adapters can cause driveline failures due to incorrect spline or incorrect operating length and can result in personal injury or death.

Look down and to the rear and make sure area is clear before operating in reverse.

Do not operate or transport on steep slopes.

Do not stop, start, or change directions sud- denly on slopes.

Watch for hidden hazards on the terrain during operation.

Stop power unit and equipment immediately upon striking an obstruction. Turn off engine, remove key, inspect, and repair any damage before resuming operation.

Continuous operation while the clutch is slip- ping could cause heat build-up resulting in fire. Adjust slip clutch pressure by tightening springs to the dimension shown in the “Owner Service” sec- tion. If clutch is set to minimum spring length, replace the friction disks as shown.

On pull-type or semi-mounted units with optional hydraulic cutting height adjustment, use a single-acting cylinder with a maximum extended

length of 28-1/4" (718 mm) from attaching point center to center.

MAINTENANCE

Before servicing, adjusting, repairing or unplug- ging, stop tractor engine, place all controls in neu- tral, set park brake, remove ignition key, and wait for all moving parts to stop.

Before dismounting power unit or performing any service or maintenance, follow these steps: disengage power to equipment, lower the 3-point hitch and all raised components to the ground, operate valve levers to release any hydraulic pres- sure, set parking brake, stop engine, remove key, and unfasten seat belt.

Before working underneath, disconnect driveline from tractor, lower wings to ground, raise cutter, and pin transport bar in raised position. Attach park- ing jack and lower to ground. Securely block all four corners of center section and each wing with jack- stands. Blocking up prevents the cutter from drop- ping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

Do not modify or alter or permit anyone else to modify or alter the equipment or any of its compo- nents in any way.

Your dealer can supply original equipment hydraulic accessories and repair parts. Substitute parts may not meet original equipment specifica- tions and may be dangerous.

To prevent contamination during maintenance and storage, clean and then cover hose ends, fit- tings, and hydraulic ports with tape.

Do not allow bystanders in the area when oper- ating, attaching, removing, assembling, or servic- ing equipment.

Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body under- neath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpect- edly and cause severe injury or death. Follow Oper- ator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

(Safety Rules continued on next page)

BW180_ SR (Rev. 12/10/2007)

Safety 9

Page 8 Page 10
Page 9
Image 9
Woods Equipment BW180HB, BW180HDQ manual Maintenance
Page 8 Page 10

BW180HDQ, BW180HD, BW180HB specifications

Woods Equipment has long been a leader in the agricultural and landscaping industry, providing exceptional products that enhance productivity and efficiency. Among its standout offerings are the BW180HB, BW180HD, and BW180HDQ models. These versatile implements are primarily designed for use with tractors, making them invaluable for a variety of tasks.

The BW180HB model is known for its high-performance capabilities combined with a compact design. One of its main features is its heavy-duty construction, which ensures durability and longevity even under strenuous conditions. The implement is equipped with a balanced weight distribution system that allows for better stability and control during operation. Additionally, the BW180HB is designed to handle a range of tasks from grading and leveling to scraping and light dozing.

Moving up the series, the BW180HD offers a higher capacity and is built for more demanding applications. This model features a robust hydraulic system that enhances lifting capabilities, allowing operators to tackle heavier loads with ease. Its advanced blade adjustment features allow for precise angle and depth control, making it ideal for a variety of terrains. The BW180HD is particularly praised for its reliability in tough environments, thanks to its reinforced frame and high-quality materials.

The BW180HDQ model represents the pinnacle of Woods Equipment's offerings in this series. It features all the capabilities of the BW180HD but includes advanced technological enhancements for improved performance. The inclusion of an automated hydraulic control system streamlines operations, enabling operators to adjust settings on-the-fly to adapt to changing conditions. Additionally, the BW180HDQ comes with integrated safety features that protect both the operator and the equipment during use.

All three models share several common characteristics that make them preferred choices among landscaping and construction professionals. They are compatible with a wide range of tractor types, ensuring versatility for various users. The quick-connect attachment points allow for rapid changes between implements, saving time and increasing productivity. With easy maintenance designs, these models ensure that downtime is minimized, allowing operators to focus on the task at hand.

In summary, the Woods Equipment BW180HB, BW180HD, and BW180HDQ models are exceptional tools for anyone looking to enhance their operational efficiency in agriculture or landscaping. With their robust features, advanced technologies, and commitment to durability, these implements represent some of the best options available in the market today.
Top Page Image Contents