DEALER SERVICE

The information in this section is written for dealer service personnel. The repair described here requires special skills and tools. If your shop is not properly equipped or your mechanics are not prop- erly trained in this type of repair, you may be time and money ahead to replace complete assemblies.

Leakage can occur at the vertical or horizontal gas- kets and shaft seals.

Leakage at the horizontal gasket or seal can be repaired without removing the gearbox from the cutter.

Before working underneath, disconnect drive- line, raise cutter, lock in transport position, and block cutter securely. Hydraulic system leak down and failure of mechanical or hydraulic system can cause equipment to drop.

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

CAUTION

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

GEARBOX MAINTENANCE

Read this entire section before starting any repair. Many steps are dependent on each other.

Repair to this gearbox is limited to replacing bear- ings, seals, and gaskets. Replacing gears, shafts, and a housing is not cost effective. Purchasing a complete gearbox is more economical.

Inspect gearbox for leakage and bad bearings. Leakage is a very serious problem and must be corrected immediately.

Bearing failure is indicated by excessive noise and side-to-side or end-play in gear shafts.

Fill gearbox with SAE 80W or 90W gear lube until it runs out the side level plug.

Seal Replacement (Figure 11)

Recommended sealant for gearbox repair is Perma- tex® Aviation 3D Form-A-Gasket or equivalent.

Seal Installation

NOTE: Proper seal installation is important. An improperly installed seal will leak.

1.Clean area in housing where seal outer diameter (OD) seats. Apply a thin coat of Permatex.

2.Inspect area of shaft where seal seats. Remove any burrs or nicks with an emery cloth.

3.Lubricate gear shaft and seal lips.

4.Place seal squarely on housing, spring-loaded lip toward housing. Select a piece of pipe or tubing with an OD that will sit on the outside edge of the seal but will clear the housing. Tubing with an OD that is too small will bow seal cage and ruin seal.

5.Carefully press seal into housing, avoiding distortion to the metal seal cage.

1.Seal

2.Pipe or tube

3.Seal seat

4.Casting

Pipe or tube must

Incorrect

Installation

Figure 11. Seal Installation

22 Dealer Service

(Rev. 4/4/2011)

MAN0224 (Rev. 7/29/2005)

Page 21 Page 23
Page 22
Image 22
Woods Equipment RCC42 manual Dealer Service, Gearbox Maintenance, Seal Replacement Figure, Seal Installation
Page 21 Page 23

RCC42 specifications

Woods Equipment has long been recognized for its commitment to quality and performance in the field of agricultural and landscape equipment. One standout product that reflects this dedication is the Woods RCC42. This rotary cutter, designed for robust performance, is particularly suitable for handling various mowing tasks, making it a favorite among professionals and avid gardeners alike.

At the heart of the Woods RCC42 is its durable construction. Made from high-quality materials, this rotary cutter is built to withstand the rigors of heavy use. Its heavy-duty frame ensures stability and longevity, ideal for tackling tough brush and dense vegetation. The RCC42 features a wide cutting width of 42 inches, allowing users to cover more ground quickly while ensuring a clean and even cut.

One of the key features of the Woods RCC42 is its superior cutting capability, which comes from its specially designed blades. The rotary cutter is equipped with sharp, high-carbon steel blades that can easily slice through even the thickest grass and brush. The blades are positioned in a way that optimizes cutting efficiency, ensuring that the mower leaves behind a finely cut finish, whether you are mowing a field or maintaining a garden.

In terms of technology, the Woods RCC42 is designed with user-friendliness in mind. The cutter is engineered to be easily attached to a variety of compact tractors, making it a versatile option for many users. Its adjustable cutting height feature allows operators to set the cutter to their desired height, accommodating different mowing conditions and vegetation types. Additionally, the RCC42 operates smoothly and quietly, making it a pleasant option for those who wish to work for extended periods without excessive noise.

Safety is another paramount consideration with the Woods RCC42. The cutter features a shielded design that provides protection to the operator while preventing debris from being ejected during operation. This thoughtful design element minimizes risks, making it a safer choice for users of all experience levels.

Overall, the Woods RCC42 rotary cutter exemplifies a balance of durability, efficiency, and user-friendly technology. Whether you are a professional landscaper or a homeowner looking to maintain your property, the RCC42 offers the reliability and performance needed to tackle even the toughest mowing jobs with ease. With its proven track record, the Woods RCC42 continues to be a benchmark in rotary cutting equipment, enhancing productivity and ensuring satisfaction for those who rely on it.
Top Page Image Contents