Operations, Control Panel, General | Woodstock W1773, W1772 manual

W1772/W1773 37" Drum Sander

OPERATIONS

Control Panel

Below is a summary of your sander control panel and the components that it controls. Use the list with Figure 23 to become familiar with your sander.

A.Sanding Drums Start Button: Starts the sanding drums.

B.Conveyor Start Button: Starts the conveyor belt.

C.Amp Draw Meter: Indicates the combined amperage draw of both motors, to help control the load so as not to damage the motor.

D.Emergency Stop Button: Stops all electrical power to motors in event of emergency.

E.Conveyor Stop Button: Stops the conveyor belt.

F.Sanding Drums Stop Button: Stops the sanding drums.

General

The Model W1772/W1773 will perform many types of oper- ations that are beyond the scope of this manual. Many of these operations can be dangerous or deadly if performed incorrectly.

The instructions in this section are written with the under- standing that the operator has the necessary knowledge and skills to operate this machine. If at any time you are experiencing difficulties performing any operation, stop using the machine!

If you are an inexperienced operator, we strongly recom- mend that you read books, trade articles, or seek training from an experienced Drum Sander operator before per- forming any unfamiliar operations. Above all, your safety should come first!

-23-

	B
A	C
A

F	D
	E

Figure 23. Control panel interface.

OFF

DO NOT investigate problems or adjust the machine while it is running. Wait until the machine is turned OFF, unplugged and all working parts have come to a complete stop before proceeding!

Always wear safety glasses and a respirator when operating this machine. Failure to comply may result in serious personal injury, allergic reactions, or respiratory problems.

OPERATIONS

Image 25

Woodstock W1773, W1772 owner manual Operations, Control Panel, General, Sanding Drums Start Button Starts the sanding drums

Contents

Drum Sander Page Contents Woodstock Technical Support Introduction Introduction Introduction Introduction Introduction Controls and Features Standard Safety Instructions Safety Always Lock Mobile Bases if Used Before Operating Machinery Additional Safety for Drum Sanders W1772 Electrical Specifications W1772 Single-Phase OperationElectrical Phase Converter W1773 220V/440V Phase OperationW1773 Electrical Specifications To rewire the Model W1773 for 440V operation, do these steps Rewiring W1773 to Items Needed for Setup SetupUnpacking Inventory If you do not hear any scraping sounds go to Step Assembly Control panel mounting bolts W1772/W1773 minimum working clearances Machine Placement Mounting to Shop Floor Lifting SanderTo place the sander in a permanent location, do these steps To connect the sander to the power source, do these steps Power ConnectionDust Collection Recommended CFM at Sander To check the gear oil, do these steps Gear Oil Check To test run the drum sander, do these steps Test Run SET Recommended Adjustments Control Panel OperationsGeneral Sanding Drums Start Button Starts the sanding drums Depth of Cut To adjust the conveyor speed, do these stepsVariable Speed To set the depth of cut, do these steps Sanding Using the Amp Draw MeterTo sand a workpiece, do these steps Sanding Tips Grit Class Choosing Sandpaper To change the paper, do these steps Paper Replacement Drum Sander Accessories Cleaning MaintenanceLubrication Lubricating gear box Step Gauge Blocks ServiceTo make the gauge blocks, do these steps To adjust V-belt tension, do these steps Belt Service To align the pulleys, do these steps Bearing Replacement Pages 38 That no obstructions prevent bearing lubrication To tension the conveyor, do these steps Conveyor Tensioning Tracking To track the conveyor, do these steps Tracking Adjusting Drums Perpendicular to Feed Direction Drum Adjustments Loosen the front drum pillow bearing lock nuts Figure Front and rear drum Adjustment locations Adjusting Drum Height & Drum-to-Conveyor Parallelism Loosen the front drum pillow bearing lock nuts , Rear right sanding drum micro Adjusting knob Pressure Roller Height Pressure roller adjustment Nuts Scale Pointer Calibration To adjust a dust scoop, do these stepsDust Scoops Table Lift Scews Marking sprocket tooth Chain To adjust the table lift screws, do these steps Emergency stop bar limit Switch W1772/W1773 Wiring Overview W1772/W1773 Control Panel W1772/W1773 control panel wiring W1772 electrical box W1772 Electrical Box 220V, 1-Ph Figures W1772 Electrical Box Wiring 220V, 1-Ph W1772 Sanding & Feed Motors W1772 sanding drum motor Wiring and start capacitors W1773 Electrical Box 220V, 3-Phase Figures W1773 Electrical Box Wiring 220V, 3-Phase W1773 440V 3-phase electrical box wiring W1773 Electrical Box 440V, 3-Phase Figures 66 W1773 Electrical Box Wiring 440V, 3-Phase W1773 Sanding Drum Motor W1773 220V sanding drum motor Wiring W1773 Feed Motor W1773 220V feed motor wiring Moving parts have come to a complete stop Troubleshooting Machine Operations Frame Parts Breakdown Parts PART# Description Frame Parts List Parts Breakdown Conveyor Parts List XPK55M Roller & Drum Parts Breakdown Micro-Adjustment Breakdown Electrical Components Currentsensor Electrical Parts List Label Placement Comments Warranty Registration BOX BELLINGHAM, WA Warranty