N(/((('Jc`[`e^KXYc\JXn
GIF9C<D |
| GFJJ@9C<:8LJ< |
| :FII<:K@M<8:K@FE |
Machine has vibration or | 1. | Motor or component is loose. | 1. | Inspect/replace stripped or damaged bolts/nuts, |
noisy operation. |
|
|
| and |
| 2. | Blade is at fault. | 2. | Replace warped, bent, or twisted blade; resharpen |
|
|
|
| dull blade. |
| 3. | Belt(s) worn or loose. | 3. | Inspect/replace belts (refer to Page 54). |
| 4. | Pulley is loose. | 4. | Realign/replace shaft, pulley, setscrew, and key as |
|
|
|
| required. |
| 5. | Motor mount loose/broken. | 5. | Tighten/replace. |
| 6. | Machine is incorrectly mounted or | 6. | Tighten/replace anchor studs in floor; relocate/shim |
|
| sits unevenly. |
| machine. |
| 7. | Arbor pulley is loose. | 7. | Retighten/replace arbor pulley with shaft and thread |
|
|
|
| locking liquid. |
8.Motor fan is rubbing on fan cover. 8. Replace dented fan cover; replace loose/damaged fan.
9. Replace arbor housing bearings; replace arbor.
10. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement.
Fg\iXk`fe
GIF9C<D |
|
| GFJJ@9C<:8LJ< |
| :FII<:K@M<8:K@FE | ||
Workpiece | has |
| burned | 1. | Sliding table is not parallel to | 1. | Make sliding table parallel to the |
edges, binds, | or | kicks |
| blade. |
| blade (Page 56). | |
back. |
|
|
| 2. | Riving knife is not aligned with the | 2. | Shim the riving knife to align it with the main |
|
|
|
| ||||
|
|
|
|
| blade. |
| blade. |
|
|
|
| 3. | Blade is warped. | 3. | Replace the blade. |
Workpiece has chip out on | 1. | Scoring blade height is incorrect. | 1. | Adjust the height of the scoring blade. | |||
the bottom edge. |
|
| 2. | Scoring blade is not aligned with | 2. | Align the scoring blade (Page 37). | |
|
|
|
|
| the main blade. |
|
|
|
|
|
| 3. | Scoring blade kerf does not match | 3. | Adjust the scoring blade kerf (Page 37). |
|
|
|
|
| the main blade. |
|
|
|
|
|
|
| |||
Sliding table saw does not | 1. | Sliding table is not parallel to | 1. | Adjust the sliding table (Page 56). | |||
cut square. |
|
|
|
| blade. |
|
|
|
|
|
| 2. | Rip fence is not parallel to blade. | 2. | Adjust the rip fence parallel to blade. |
|
|
|
| 3. | Crosscut fence is not perpendicular | 3. | Adjust the crosscut fence perpendicular to the blade |
|
|
|
|
| to the blade. |
| (Page 58). |
|
|
|
|
| |||
Fence hits table top when | 1. | Front rail is too low. | 1. | Raise the front rail. | |||
sliding across table. |
| 2. | Rip fence roller is too low. | 2. | Adjust the rip fence roller. | ||
|
|
|
|
| |||
Blade does not reach 90˚, | 2. | Blade stop bolts are out of adjust- | 2. | Adjust the stop bolts (Page 55). | |||
or blade does not reach |
| ment. |
|
| |||
45˚. |
|
|
|
|
|
|
|
The rip fence scale is not | 1. | The rip fence scale is out of calibra- | 1. | Adjust the rip fence scale. | |||
accurate. |
|
|
|
| tion or was not set up correctly. |
|
|
|
|
|
|
|
|
| |
Handwheels | for | blade | 1. | Shipping braces still attached. | 1. | Remove shipping braces. | |
adjustments | will | not turn | 2. | Lock knob is tight. | 2. | Release the lock knob. | |
or are difficult to turn. | 3. | Gears caked with dust. | 3. | Clean out dust and grease the gears. | |||
|
|
|
| ||||
|
|
|
|
|
|
|
|
