Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology XPD 60-9, XPD 7.5-67 AC Input Power Connection, V and 18 V, p, AC Input Cord

Models: XPD 18-30 XPD 33-16 XPD 120-4.5 XPD 7.5-67 XPD 60-9

1 56

Download 56 pages 43.26 Kb

Page 30

AC Input Power Connection

Section 2. Installation

AC Input Power Connection

AC Input Power Connection

WARNING

There is a potential shock hazard if the power supply chassis and cover are not connected to an electrical ground via the safety ground in the AC input connector. Ensure that the power supply is connected to a grounded AC outlet with the recommended AC input cord configured for the available line voltage as described in this section.

WARNING

Disconnect AC power from the unit before removing the cover. Even with the front panel power switch in the OFF position, live line voltages are exposed when the cover is removed. Repairs must be made only by experienced service technicians.

CAUTION

When the power switch is turned on, the output voltage or current previously set will be applied to loads

AC Input The AC input connector is a standard IEC 15 A, 250 V male connector located on Connector the power supply’s rear panel. See Figure 1.2 500 Watt Power Supply Rear Panel

(7.5 V and 18 V), p. 13.

AC Input

Cord

WARNING

The AC input cord is the disconnect device for the power supply. The plug must be readily identifiable by and accessible to the operator. The input cord must be no longer than 9.85 feet (3 m).

The AC input cord that we provide is appropriate to the country of destination. If you require a special cord, contact us.

28	Operating Manual for XPD Series Power Supply

Image 30

Xantrex Technology XPD 60-9, XPD 7.5-67, XPD 120-4.5, XPD 33-16 manual AC Input Power Connection, V and 18 V, p, AC Input Cord

Contents

XPD 500 Watt Series Programmable DC Power Supply XPD XPD XPD XPD XPDOperating Manual Page XPD Series Programmable DC Power SupplyOperating Manual for How do you get service? Limited WarrantyProof of purchase may be in any one of the following forms Disclaimer Product Information About Your Power Supply WARNING Limitations on UsePower Supply Safety CautionsManual Revisions Who Should Use This ManualMain Sections About This ManualPower Supply Safety Markings Operating Manual for XPD Series Power SupplyAbout This Manual Contents Section Features and SpecificationsSection 2. Installation Section Local Operation Section Remote Operation Section 1. Features and Specifications Features and OptionsDescription “Mechanical Specifications” on page “Functional Tests” on page Front Panel Controls“Standard Operation” on page 35l Figure 1.2 500 Watt Power Supply Rear Panel 7.5 V and 18 Rear Panel ConnectorsSection 1. Features and Specifications 500 Watt Power Supply Rear Panel 33 V to 120Output The J210 connector provides access to the following functions Reference Section 1. Features and Specifications1. The TTL shutdown circuit is isolated to 500 V from the power supply output and chassis NameSection 1. Features and Specifications WiringMaking J210 Connections 120 V, 4.5 A power supplyModels Electrical SpecificationsSection 1. Features and Specifications 7.5-67Section 1. Features and Specifications Additional SpecificationsInput Conditions Additional SpecificationsAdditional Characteristics Remote Programming and MonitoringSection 1. Features and Specifications Section 1. Features and Specifications Environmental SpecificationsMechanical Specifications Environmental SpecificationsSection 1. Features and Specifications Mounting“Inspection, Cleaning, and Section 2. InstallationBasic Setup Procedure “AC Input Power Connection”Cleaning Inspection, Cleaning, and Packaging“Returning Power Supplies to the Manufacturer” on page InitialReturning Power Supplies to the Manufacturer If you are returning a product from outside of the USA or CanadaPackaging for Shipping or Storage Location, Mounting, and Ventilation Rack MountingAC Input Power Connection 7.5 V and 18 V, pAC Input Cord Power-on Check Voltage Mode Operation Check Current Mode Operation Functional TestsCheck Load Connection Making Load Connections Section 2. InstallationMultiple InductiveLoads rated supply outputRemote Sensing Sense Wiring Operating Modes and Automatic Crossover Section 3. Local OperationStandard Operation IntroductionOperation Setting theConstant Current LimitSee “Using Over Voltage Protection Shipped Configuration Local Control ModeSetting the Supply to Operate in CI Mode Automatic Mode Crossover OVP” on page 38 , for theUsing Over Voltage Protection OVP Using the Shutdown Function Controlling Shutdown Function via J210 ConnectorMaster-Slave Tracking Using Multiple Supplies Using Multiple SuppliesSection 3. Local Operation Configuring Multiple Supplies for Series Operation Voltage Mode Only Series OperationConfiguring Multiple Supplies for Parallel Operation Figure 3.3 Parallel OperationConfiguring Multiple Supplies for Split Supply Operation Load LinesPositive-negative supply To obtain a positive-negative supply, connect the negative output terminal of one supply to the positive terminal of the second supply. The positive output terminal of the first supply now provides a positive voltage relative to the common connection. The negative output terminal of the second supply provides the negative voltage. The current limits can be set independently of each other. The maximum current available in split operation is equal to the rated output of the supplies User Diagnostics Trouble Shooting for OperatorsEmergency Shutdown Unusual or Erratic Operation See “Using the Shutdown source. See “AC Input PowerSee “Using Over Voltage Connection” on page30, and “Remote Sensing” on Operation” on pageSee “Load Connection” on page pageUser Diagnostics Operating Manual for XPD Series Power SupplySection 3. Local Operation Remote Section 4. Remote OperationRemote Analog Programming of Output Voltage and Current Limit DigitalProgramming Output Voltage with a 0-10 Vdc Voltage Source Readback and Status IndicatorsOptions Programming Output Current with a0-10 Vdc Voltage SourceStatus Flags Operating Manual for XPD Series Power Supply Section 4. Remote OperationStatus Flags Page 604 422 8595 Tel 604 421 3056 Fax Xantrex Technology Inc8999 Nelson Way Burnaby, British Columbia Canada V5A 4B5 800 667 8422 Toll Free North America prg.info@xantrex.com