Manuals / Xantrex Technology / Computer Equipment / Power Supply

Xantrex Technology XPD 33-16, XPD 60-9, XPD 7.5-67, XPD 120-4.5 manual Cautions, Power Supply Safety

Models: XPD 18-30 XPD 33-16 XPD 120-4.5 XPD 7.5-67 XPD 60-9

1 56

Download 56 pages 43.26 Kb

Page 8

Cautions

Warnings Warnings and cautions are defined and formatted in this manual as shown below. and

Cautions

WARNING

Describes a potential hazard which could result in injury or death, or, a procedure which, if not performed correctly, could result in injury or death.

CAUTION

Describes a procedure which, if not performed correctly, could result in damage to data, equipment, or systems.

Power

Supply

Safety

WARNING—High Energy and High Voltage

Exercise caution when using and calibrating a power supply. High energy levels can be stored at the output voltage terminals on a power supply in normal operation. In addition, potentially lethal voltages exist in the power circuit and on the output and sense connectors of a power supply with a rated output greater than 40 V. Filter capacitors store potentially dangerous energy for some time after power is removed.

CAUTION

Operate the power supply in an environment free of flammable gases or fumes. To ensure that the power supply’s safety features are not compromised, use the power supply as specified in this manual and do not substitute parts or make any unauthorized modifications. Contact the service technician for service and repair help. Repairs must be made by experienced service technicians only.

CAUTION

For Use as a Battery Charger

When you are using any of these power supplies for battery charging applications, it is essential to provide an appropriately sized fuse or circuit breaker in series between the power supply output and the battery.

Installation of a protector (fuse or DC circuit breaker) rated for about 115% of the maximum current rating of the power supply and designed specifically to interrupt the DC voltage of the battery, will provide adequate reverse polarity current protection. Where several power supplies are in parallel, it is best to fuse each one, rather than one large fuse for all.

vi	Operating Manual for XPD Series Power Supply

Image 8

Xantrex Technology XPD 33-16, XPD 60-9, XPD 7.5-67, XPD 120-4.5, XPD 18-30 manual Cautions, Power Supply Safety

Contents

Operating Manual XPD 500 Watt Series Programmable DC Power SupplyXPD XPD XPD XPD XPD Page Operating Manual for XPD SeriesProgrammable DC Power Supply How do you get service? Limited WarrantyProof of purchase may be in any one of the following forms Disclaimer Product Information About Your Power Supply WARNING Limitations on UsePower Supply Safety CautionsWho Should Use This Manual Main SectionsManual Revisions About This ManualAbout This Manual Power Supply Safety MarkingsOperating Manual for XPD Series Power Supply Section 2. Installation ContentsSection Features and Specifications Section Local Operation Section Remote Operation Description Section 1. Features and SpecificationsFeatures and Options “Standard Operation” on page 35l “Mechanical Specifications” on page “Functional Tests” on pageFront Panel Controls Rear Panel Connectors Section 1. Features and SpecificationsFigure 1.2 500 Watt Power Supply Rear Panel 7.5 V and 18 500 Watt Power Supply Rear Panel 33 V to 120Output The J210 connector provides access to the following functions Section 1. Features and Specifications 1. The TTL shutdown circuit is isolated to 500 V from the power supply output and chassisReference NameWiring Making J210 ConnectionsSection 1. Features and Specifications 120 V, 4.5 A power supplyElectrical Specifications Section 1. Features and SpecificationsModels 7.5-67Additional Specifications Input ConditionsSection 1. Features and Specifications Additional SpecificationsSection 1. Features and Specifications Additional CharacteristicsRemote Programming and Monitoring Environmental Specifications Mechanical SpecificationsSection 1. Features and Specifications Environmental SpecificationsSection 1. Features and Specifications MountingSection 2. Installation Basic Setup Procedure“Inspection, Cleaning, and “AC Input Power Connection”Inspection, Cleaning, and Packaging “Returning Power Supplies to the Manufacturer” on pageCleaning InitialReturning Power Supplies to the Manufacturer If you are returning a product from outside of the USA or CanadaPackaging for Shipping or Storage Location, Mounting, and Ventilation Rack MountingAC Input Cord AC Input Power Connection7.5 V and 18 V, p Check Power-on Check Voltage Mode Operation Check Current Mode OperationFunctional Tests Load Connection Making Load Connections Section 2. InstallationInductive LoadsMultiple rated supply outputRemote Sensing Sense Wiring Section 3. Local Operation Standard OperationOperating Modes and Automatic Crossover IntroductionSetting the ConstantOperation Current LimitShipped Configuration Local Control Mode Setting the Supply to Operate in CI Mode Automatic Mode CrossoverSee “Using Over Voltage Protection OVP” on page 38 , for theUsing Over Voltage Protection OVP Master-Slave Tracking Using the Shutdown FunctionControlling Shutdown Function via J210 Connector Section 3. Local Operation Using Multiple SuppliesUsing Multiple Supplies Configuring Multiple Supplies for Series Operation Voltage Mode Only Series OperationConfiguring Multiple Supplies for Parallel Operation Figure 3.3 Parallel OperationConfiguring Multiple Supplies for Split Supply Operation Load LinesPositive-negative supply To obtain a positive-negative supply, connect the negative output terminal of one supply to the positive terminal of the second supply. The positive output terminal of the first supply now provides a positive voltage relative to the common connection. The negative output terminal of the second supply provides the negative voltage. The current limits can be set independently of each other. The maximum current available in split operation is equal to the rated output of the supplies Emergency Shutdown Unusual or Erratic Operation User DiagnosticsTrouble Shooting for Operators source. See “AC Input Power See “Using Over VoltageSee “Using the Shutdown Connection” on pageOperation” on page See “Load Connection” on page30, and “Remote Sensing” on pageSection 3. Local Operation User DiagnosticsOperating Manual for XPD Series Power Supply Section 4. Remote Operation Remote Analog Programming of Output Voltage and Current LimitRemote DigitalReadback and Status Indicators OptionsProgramming Output Voltage with a 0-10 Vdc Voltage Source Programming Output Current with a0-10 Vdc Voltage SourceStatus Flags Status Flags Operating Manual for XPD Series Power SupplySection 4. Remote Operation Page Xantrex Technology Inc 8999 Nelson Way Burnaby, British Columbia Canada V5A 4B5604 422 8595 Tel 604 421 3056 Fax 800 667 8422 Toll Free North America prg.info@xantrex.com