Xerox 120, 144 specifications Product Space & Power Requirements

Xerox Nuvera® 100/120/144 EA Digital Production System - Customer Expectations Document

Product Space & Power Requirements

Item	Xerox Nuvera® 100/120/144 EA	Comments
	Digital Production System
Size – Printer w/ 1 SFM	132” (W) X 29 ” (D) X 61.6 ” (H)
/ Scanner & MFF	3353 mm x 737 mm x 1565 mm
Size – Printer w/ 1 SFM	125” (W) X 29 ” (D) X 61.6 ” (H)	Printer Digital Tower 61.6” (1565 mm) (Height)
& SEM / FTM	3175 mm x 737 mm x 1565 mm	DFA finishing devices vary by device*.
Size – Printer w/ 1 SFM	124” (W) X 29 ” (D) X 61.6 ” (H)
& SEM / BFM	3150 mm x 737 mm x 1565 mm
Width of additional	31.7”, 805mm	Optional
SFM
Width of BFM Plus	49”, 1233mm	Optional, BFM Plus and Interface Module used with BFM (with top
		tray) in dual BFM installations.
Service Space	Fixed: 163” (W) x 112” (D)	- Fixed (stationary) installation: rear of the system should be at least
(MFF Config.)	( 4140mm x 2839mm)	30” from the wall, machine, or rear obstruction..
	Moveable: 163” (W) x 92” (D)	- Moveable installation: rear of the system should be at least 10” from
	( 4140mm x 2336.8mm)	the wall and must be on mobility plates OR hard surface floor AND
		with no more than 4 modules including MFF and MFF Interface
		Module.
Service Space	BFM: 145” (W) x 112” (D)	At least 30” from the wall in rear.
(BFM / FTM Config.	3683mm x 2839 mm	DFA finishing will increase width - FTM config. dimensions do not
with SEM)	FTM: 143” (W) x 112” (D)	include DFA Finisher(s) dimensions or service space.
	3632mm x 2839 mm
Weight	1,753 lb. (795.2 kg)	With consumables loaded, except media
(MFF Config. w/	Additional SFM – 423 lbs. (192 kg)
scanner)
Weight	BFM: 1763 lb. (800 kg)	With consumables loaded, except media
(BFM / FTM Config.	FTM: 1713 lb. (777 kg)	FTM config. listing does not include DFA Finisher(s) weight.
with SEM)	Additional SFM – 423 lbs. (192 kg)
Power Requirements	187 – 240 Volts AC (Nominal), 50 Amp ,	• UL & cUL compliant
North America / Japan	50/60 Hz wall service	• Complies with the FEMP (Federal Energy Management Program)
(MFF / BFM Finishing)	Note – FTM and DFA finishers will require	via the machine circuit breaker (CB); with the CB switched off, the
		system consumes less than 1 watt.
	additional power	• Energy Star (eStar) compliant**
		• Environmental Choice (Canada)**
		• Complies with Section 508 of the ADA Rehabilitation Act
Power Requirements	187 – 240 Volts AC (Nominal), 30 Amp +	• Units are compliant with applicable EU directives and are CE
Europe / FX-IBG	20 Amp (2) , 50/60 Hz wall service	marked
	Feeders and Finisher modules (BFMs) will
	need additional 187 – 240 VAC (Nominal),
	20 Amp, 50/60 Hz wall service
	Note – FTM and DFA finishers will require
	additional power

*- Please refer to supported inline DFA finishing devices Solution Planning Guides for Product Space and Power Requirements.

**- the following configuration is not Energy Star compliant:

•100 ppm printer-only configuration with a BFM

- 14 -