Item | Function | Page | |
|
|
| |
SPEAKER IMP. | Changes the speaker impedance setting. | ||
|
|
| |
REMOTE SENSOR | Turns on/off of the remote control sensor on the main unit. | ||
|
|
| |
REMOTE CON AMP | Selects the unit’s remote control ID. | ||
|
|
| |
TUNER FRQ STEP | (Asia and General models only) | ||
Changes the FM/AM tuning frequency setting. | |||
|
| ||
|
|
| |
TV FORMAT | Switches the video signal type. | ||
|
|
| |
MONITOR CHECK | Removes the limitation on HDMI video output. | ||
|
|
| |
RECOV./BACKUP | Creates backup of the settings of the unit, or recovers the settings | ||
from the backup. | |||
|
| ||
|
|
| |
INITIALIZE | Restores the default settings. | ||
|
|
| |
FIRM UPDATE | Updates the firmware. | ||
|
|
| |
VERSION | Checks the version of firmware currently installed on the unit. | ||
|
|
|
DOCK | SPIMP.- | S P E A K E R I M P . |
|
TAG |
|
| |
HD |
| MUTE VOLUME | |
STEREO TUNED PRE AMP PARTY | |||
| ZONE ZONE ZONE | 8 M I N | ADAPTIVE DRC |
IN OUT1 OUT2 2 3 4 | PL L C R PR | ||
ENHANCER SLEEP |
| SL SW1 SW SW2 SR | |
| HD 3 |
| PL SBL SB SBR PR |
Change the unit’s speaker impedance settings depending on the impedance of the speakers connected.
Settings
6 | Ω MIN | Select this option when you connect | |
can also use | |||
|
| ||
|
|
| |
8 | Ω MIN (default) | Select this option when you connect | |
unit. | |||
|
| ||
|
|
|
DOCK | SPIMP.- | R E M O T E S E N S O R |
|
TAG |
|
| |
HD |
| MUTE VOLUME | |
STEREO TUNED PRE AMP PARTY | |||
| ZONE ZONE ZONE | O N | ADAPTIVE DRC |
IN OUT1 OUT2 2 3 4 | PL L C R PR | ||
ENHANCER SLEEP |
| SL SW1 SW SW2 SR | |
| HD 3 |
| PL SBL SB SBR PR |
Turn on/off the remote control sensor on the main unit. While the remote control sensor is turned off, you cannot control the unit from the remote control.
Settings
ON (default) | Turns on the remote control sensor. |
OFF | Turns off the remote control sensor. |
|
|
DOCK | SPIMP.- | R E M O T E C O N A M P MUTE VOLUME | |
TAG |
| ||
HD |
| ||
STEREO TUNED PRE AMP PARTY | |||
| ZONE ZONE ZONE | I D 1 | ADAPTIVE DRC |
IN OUT1 OUT2 2 3 4 | PL L C R PR | ||
ENHANCER SLEEP |
| SL SW1 SW SW2 SR | |
| HD 3 |
| PL SBL SB SBR PR |
Change the unit’s remote control ID so that it matches the remote control’s ID (default: ID1). When using multiple Yamaha AV receivers, you can set each remote control with a unique remote control ID for its corresponding receiver.
Settings
ID1 (default), ID2
■Changing the remote control ID of the remote control
Perform each of the following steps within 1 minute. Otherwise, the setting will be automatically canceled.
1Press CODE SET on the remote control.
2Press RECEIVER.
3Use the numeric keys to enter “5019” (ID1) or “5020” (ID2).
Once the remote control ID is registered successfully, SOURCE blinks twice.
If it blinks six times, registration failed. Repeat from Step 1.
• The registered remote control codes (p.119) are not cleared even if you change the remote control ID.
CONFIGURATIONS ➤ Configuring the system settings (ADVANCED SETUP menu) | En 116 |
|
|