Problem | Cause | Remedy | |
| The TV is set to output audio from the TV speakers. | Change the audio output setting on your TV so that the TV audio is output from the | |
| speakers connected to the unit. | ||
|
| ||
|
|
| |
No sound from the TV (when HDMI Control is | (If the TV is connected to the unit with an audio cable) | Use “TV Audio Input” in the “Setup” menu to select the correct audio input jack | |
used). | The TV audio input setting does not match the actual connection. | ||
|
|
| |
| (If you are trying to use ARC) | Set “ARC” in the “Setup” menu to “On” (p.106). Also, enable ARC on the TV. | |
| ARC is disabled on the unit or TV. | ||
|
| ||
|
|
| |
Only the front speakers work on multichannel | The playback device is set to output | To check it, use “Audio Signal” in the “Information” menu (p.114). If necessary, | |
audio. | PCM) only. | change the digital audio output setting on the playback device. | |
|
|
| |
Noise/hum is heard. | The unit is too close to another digital or radio frequency device. | Move the unit further away from the device. | |
|
| ||
The cable connecting the unit and playback device is defective. | If there is no problem with the connection, replace with another cable. | ||
| |||
|
|
| |
| The volume of the unit is too high. | Turn down the volume. If “ECO Mode” in the “Setup” menu is set to “On”, set it to | |
The sound is distorted. | “Off” (p.113). | ||
| |||
|
| ||
| A device connected to the unit’s output jacks is not turned on. | Turn on all devices connected to the unit’s output jacks. | |
|
|
|
Video
Problem | Cause | Remedy | |
| Another input source is selected on the unit. | Select an appropriate input source with the input selection keys. | |
|
|
| |
| Another input source is selected on the TV. | Switch the TV input to display the video from the unit. | |
No video. |
|
| |
The video signal output from the unit is not supported by the TV. | Set “MONITOR CHECK” in the “ADVANCED SETUP” menu to “YES” (p.117). | ||
| |||
|
|
| |
| The cable connecting the unit and TV (or playback device) is | If there is no problem with the connection, replace with another cable. | |
| defective. | ||
|
| ||
|
|
| |
|
| To check the information about the current video signal (resolution), use “Video | |
| The input video signal (resolution) is not supported by the unit. | Signal” in the “Information” menu (p.114). For information about video signals | |
|
| supported by the unit, see “HDMI signal compatibility” (p.138). | |
No video from the playback device (connected to |
|
| |
The TV does not support HDCP | Refer to the instruction manuals for the TV and check the TV’s specifications. | ||
the unit with HDMI). | |||
Protection). | |||
|
| ||
|
|
| |
| The number of devices connected to the HDMI OUT jack is over | Disconnect some of the HDMI devices. | |
| the limit. | ||
|
| ||
|
|
| |
| The TV is not connected to the unit via HDMI. | You can display the menu of the unit on the TV only when they are connected with | |
The menu of the unit is not displayed on the TV. | an HDMI cable. If necessary, use an HDMI cable to connect them (p.25 to 28). | ||
| |||
|
| ||
| Another input source is selected on the TV. | Switch the TV input to display the video from the unit (HDMI OUT jack). | |
|
|
|
APPENDIX ➤ Troubleshooting | En 128 |
|
|