RECORDING

To edit tracks dividing them to

1 7 8side A and side B automatically (Auto editing function)

 

 

 

 

 

 

 

To use tapes effectively, tracks on a CD are automatically

 

 

 

 

 

 

 

rearranged between side A and side B to best utilize the

 

 

 

 

 

 

 

length of the tape.

 

 

 

 

 

 

 

 

 

When the desired tracks are selected in program selection,

 

 

 

 

 

 

6

the tracks stored in memory are automatically divided

 

 

 

 

 

 

between side A and side B.

 

 

 

 

 

 

 

 

1 Select the CD position and load the CD to be recorded.

 

 

 

 

 

 

 

2 Load a tape into the tape “b” cassette compartment.

 

 

 

 

 

 

 

* Rewind the tape onto the left-side reel.

 

 

 

 

 

 

 

3 When recording with the Dolby NR system, set the

 

 

 

 

 

 

 

DOLBY NR switch to B or C; if not, set it to OFF.

 

 

 

 

 

 

 

* For selection of the Dolby B or C position, refer to the

 

 

 

 

 

 

 

 

“Dolby B and C Type Noise Reduction” on page 24.

 

 

 

 

 

 

 

4 Set the REVERSE MODE switch to

.

 

 

 

 

 

 

 

5 Press the REC button.

 

 

 

 

 

 

 

 

* The indicator beside the REC button lights up and the

 

 

 

 

 

 

 

 

play indicators flash.

 

 

 

 

 

 

 

 

6 Press the C46, C60 or C90 according as the length of the

 

 

 

 

 

 

 

tape to be used.

 

 

4

3

 

5

 

2

When using tapes other than C46, C60 or C90

 

 

 

 

 

 

 

Press the

or

button to adjust the time (minute by

 

 

 

 

 

 

 

minute).

 

 

 

 

 

 

 

 

 

 

Adjustable range is from C10 to C99.

 

 

 

 

 

 

 

 

It is also possible to use the track number input buttons on

 

 

 

 

 

 

 

the remote control to set the tape length.

 

1

2

3

4

5

 

For a tape length of C30, press the “+10”, “+10”, “+10”

 

 

 

 

 

 

 

 

6

7

8

9

0

 

 

and “0”. (Press each button within 3 seconds after the

 

 

 

 

 

 

 

 

 

PROG

CLEAR

CALL

TIME

+10

 

 

previous one has been pressed.)

 

 

 

 

 

 

 

1

7 Press the EDIT button.

 

 

REPEAT

 

 

 

CD

* Tracks on the CD are automatically divided between

 

 

 

 

 

 

5

 

 

 

BAND

TUNER

 

 

side A and side B.

 

 

 

 

 

 

 

 

 

 

 

b

 

 

 

 

8

* The number of tracks, total time and track numbers to

 

 

 

 

 

 

 

a

 

 

 

 

 

be recorded on side A and side B are displayed for

 

 

 

 

 

 

 

 

approximately 4 seconds. (When there are tracks

 

HALL

JAZZ CLUB ROCK CNCT

OFF

TAPE

 

 

which can not be recorded, the “TIME OVER” indicator

 

 

 

 

 

 

 

 

 

POWER

AUX

DAT

- VOLUME +

 

 

will light up.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 Press the play button of the CD.

 

 

 

 

 

 

 

 

* CD playback and recording start approximately 9

 

 

 

 

 

 

 

 

seconds after the tape starts (after the part of the tape

 

 

 

 

 

 

 

 

on which recording can not be performed is wound).

To cancel auto editing function

Before recording, press the stop button of the CD.

To stop recording

Press the stop button of the tape.

(At this time, CD playback automatically stops.)

E-28