Manuals / Brands / Home Audio / Speaker System / Yamaha / Home Audio / Speaker System

Yamaha CC-75 Antenna connection, English, CONNECTIONS, (1) Supplied FM antenna, (3) External FM antenna, (4) External AM (MW/LW) antenna

1 54

Download 54 pages, 933.68 Kb

CONNECTIONS

Never plug the AC supply lead of this system into the AC outlet until all connections are completed.

English

(1)

		AM
		ANT
		GND
(2)	75Ω	FM
(2)	UNBAL.	ANT

15 m (49 feet)

(4)

(3)

7.5 m (25 feet)

Earth rod

AM

ANT

GND

75ΩFM

UNBAL. ANT

or

*For U.K. and Europe models, “AM” is replaced by “MW LW”.

100 kHz	FM	50 kHz
10 kHz	AM	9 kHz

Antenna connection

(1) Supplied FM antenna

Connect the FM antenna wire to the corresponding terminal and direct the FM antenna wire to the direction where the strongest signal can be received.

(2) Supplied AM (MW/LW) loop antenna

Connect the AM (MW/LW) loop antenna wires to the corresponding terminals. Position the AM (MW/LW) loop antenna for optimum reception. Place the AM (MW/LW) loop antenna on a shelf etc., or install it on the rack or wall with screws (not supplied).

Notes

•When static is still heard even after adjusting the position of the AM (MW/LW) loop antenna, try reversing the wire connections (top to bottom).

•Do not place the AM (MW/LW) loop antenna on the unit. It will result in noise generation, since the unit is equipped with digital electronics. Place the AM (MW/LW) loop antenna away from the unit.

(3) External FM antenna

Use an external FM antenna instead of an indoor FM antenna if you need better reception. Consult your dealer.

(4) External AM (MW/LW) antenna

Use an external AM (MW/LW) antenna if you need better reception. Consult your dealer.

Note

When using an external AM (MW/LW) antenna, be sure to keep the wire of the AM (MW/LW) loop antenna connected.

FREQUENCY STEP switch (General model only) Because the interstation frequency spacing differs in different areas, set the FREQUENCY STEP switch (located at the rear) according to the frequency spacing in your area. Before setting this switch, disconnect the AC supply lead of this unit from the AC outlet.

FREQUENCY STEP

E-7

Contents

Page ●After unpacking, check that the following parts are contained ●Après le déballage, vérifier que les pièces suivantes sont incluses ●Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind ●Kontrollera efter det apparaten packats upp att följande delar finns med ●Controleer na het uitpakken of de volgende onderdelen voorhanden zijn 1CDC-S75 2RX-S75 EFG H WX Y H 3KXW-S75 cd e f g h ij 4 NX-S75 HIJK L To AC outlet Vers la prise c.a Zur Netzsteckdose Till nätuttag Alla presa AC INTRODUCTION English FEATURES •75W + 75W (6Ω) Output Power, 10% THD, 1 kHz •Random Access Programmable CD Playback PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT ■Do not operate this unit upside-down.It may overheat, possibly causing damage ■Never open the cabinet. If something drops into the set, contact your dealer Condensation can cause the unit to malfunction. To eliminate condensation: •CD pickup SETTING UP THE SYSTEM Setup examples KXW-S75 RX-S75 CDC-S75 (See figure 1 and 2 on page 3 – 5 at the beginning part of this manual.) 1Disc Table 2Stop Button: 3Disc Selector Buttons 4TIME Button Names of control buttons (See figure 5 on page 7 at the beginning part of this manual.) 1Remote Control Transmitter Window 2Preset Station Number Buttons 3A, B, C, D, E Selector Buttons Loading the batteries for the remote control transmitter (See figure 6 on page 7.) (See figure 8 on page 8.) Proper use of the remote control transmitter (See figure 7 on page 7.) Antenna connection Speaker connection System connection (See figure 0 on page 8.) Connecting the AC supply lead (See figure A on page 8.) SETTING THE CLOCK Changes Minute Second 2 While pressing the TIME ADJ button, press the HOUR button and set the hour The hour setting will not advance even if minute is advanced from “59” to “00” Volume Balance Tone Listening to the music with the DSS Care of compact discs CD playback Direct-selectionplay Skip search Manual search Program play To stop program play •Press the stop button. The first programmed track number will be displayed To resume playback, press the play/pause To cancel a programmed sequence There are several methods as described below Repeat play Random play Switching the time display Automatic tuning Manual tuning Preset tuning Automatic preset tuning Displaying RDS data To turn the unit into the RDS mode Calling a preset RDS station by the program type (PTY SEEK) Other functions which make use of RDS data service General information Tape A or tape B playback Winding the tape Searching for the beginning of a desired selection Continuous playback CD synchronized recording To stop recording temporarily 1 Press the stop button of the CD player 2 Choose the selection to be recorded next by using the control transmitter) To stop recording Recording CD(s) on both sides of a tape automatically Automatic tape-editing Page To record programmed tracks from one or more discs 2 Follow steps 3–6on page 3 Press the PROG button 4 If necessary, select a desired disc by pressing the DISC SKIP button 5 Select the desired track number by pressing the track number input buttons Recording from the built-intuner Dubbing Erasing recorded tapes Timer play ➂ At ON TIME/time setting mode TIME ADJ TIMER HOUR MINUTE ➃At OFF TIME/time setting mode To cancel the timer play setting Timer recording (To record a tuner program) Sleep timer operation Using the timer and the sleep timer at the same time <U.S.A., Canada, Australia, Singapore and General models <U.K. and Europe models Internal care External care TROUBLESHOOTING SPECIFICATIONS