Manuals / Brands / Home Audio / Speaker System / Yamaha / Home Audio / Speaker System

Yamaha CC-75 Timer recording, (To record a tuner program), POWER, TUNER, input, POWER, button, DISPLAY, In step, Receiver, selector, Tape Deck, INPUT SELECTOR

1 54

Download 54 pages, 933.68 Kb

HOW TO USE THE BUILT-IN TIMER

INPUT SELECTOR

POWER

Receiver

DISPLAY TIMER TIMER REC

Tape Deck

2 1

CD

	1	2	3	4	5
	1	2	3	4	5
	6	7	8
	6	7	8	9	0
	A	B	C	D	E
	TIME	PROG	TAPE	EDIT	+10
	REPEAT RANDOM		STOP	PLAY/PAUSE OPEN/CLOSE
	MODE	DISC SKIP			TUNER	TUNER
		PLAY	STOP	PLAY		TUNER
	DECK	PLAY	STOP	PLAY		input
	DECK				TAPE	input
	A/B		REC/PAUSE		INPUT	selector
	EFFECT LEVEL		SP/PHONES MODE		DSS	selector
	EFFECT LEVEL		SP/PHONES MODE		DSS	button
	-	+				button
POWER	POWER SLEEP		DISPLAY	VOLUME
POWER				-	+

DISPLAY

Timer recording

(To record a tuner program)

1 Load a blank tape into the DECK B cassette compartment.2 If desired, change the setting of the reverse mode and the Dolby NR position.

3 Tune to the station of which program you want to record. 4 Follow step 2 of the “Timer play” on page 38 and 39.

*In step ➁, select the TUNER position with the INPUT SELECTOR control, and then press the TIMER REC button. (“REC” will flash on the display.)

*In step ➂, set the time when you want to begin the timer recording.*In step ➃, set the time when you want to finish the timer recording.5 Press the TIMER button.(The power will be turned off automatically.)

*If a normal display mode (the state which had been selected before you began setting the timer recording) is restored before you press the TIMER button, select and follow either of the two methods below.

•Press the DISPLAY button, and then press the TIMER button. (The power is still on.)

•Press the POWER switch to turn the power off, and then press the TIMER button. (The power is turned off.)

To confirm the timer time settingPress the DISPLAY button.To cancel the setting of timer recording

Press the DISPLAY button once or more so that “REC” flashes on the display. While “REC” is flashing, press the TIMER REC button.

*Unless the AC supply lead is unplugged or there is a power failure for more than 5 minutes, the time set on the timer will be retained until it is reset.

Note

When the timer recording is finished, the timer setting is automatically canceled to avoid repeating timer recording of the same setting.

E-40

Contents

Page ●After unpacking, check that the following parts are contained ●Après le déballage, vérifier que les pièces suivantes sont incluses ●Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind ●Kontrollera efter det apparaten packats upp att följande delar finns med ●Controleer na het uitpakken of de volgende onderdelen voorhanden zijn 1CDC-S75 2RX-S75 EFG H WX Y H 3KXW-S75 cd e f g h ij 4 NX-S75 HIJK L To AC outlet Vers la prise c.a Zur Netzsteckdose Till nätuttag Alla presa AC INTRODUCTION English FEATURES •75W + 75W (6Ω) Output Power, 10% THD, 1 kHz •Random Access Programmable CD Playback PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT ■Do not operate this unit upside-down.It may overheat, possibly causing damage ■Never open the cabinet. If something drops into the set, contact your dealer Condensation can cause the unit to malfunction. To eliminate condensation: •CD pickup SETTING UP THE SYSTEM Setup examples KXW-S75 RX-S75 CDC-S75 (See figure 1 and 2 on page 3 – 5 at the beginning part of this manual.) 1Disc Table 2Stop Button: 3Disc Selector Buttons 4TIME Button Names of control buttons (See figure 5 on page 7 at the beginning part of this manual.) 1Remote Control Transmitter Window 2Preset Station Number Buttons 3A, B, C, D, E Selector Buttons Loading the batteries for the remote control transmitter (See figure 6 on page 7.) (See figure 8 on page 8.) Proper use of the remote control transmitter (See figure 7 on page 7.) Antenna connection Speaker connection System connection (See figure 0 on page 8.) Connecting the AC supply lead (See figure A on page 8.) SETTING THE CLOCK Changes Minute Second 2 While pressing the TIME ADJ button, press the HOUR button and set the hour The hour setting will not advance even if minute is advanced from “59” to “00” Volume Balance Tone Listening to the music with the DSS Care of compact discs CD playback Direct-selectionplay Skip search Manual search Program play To stop program play •Press the stop button. The first programmed track number will be displayed To resume playback, press the play/pause To cancel a programmed sequence There are several methods as described below Repeat play Random play Switching the time display Automatic tuning Manual tuning Preset tuning Automatic preset tuning Displaying RDS data To turn the unit into the RDS mode Calling a preset RDS station by the program type (PTY SEEK) Other functions which make use of RDS data service General information Tape A or tape B playback Winding the tape Searching for the beginning of a desired selection Continuous playback CD synchronized recording To stop recording temporarily 1 Press the stop button of the CD player 2 Choose the selection to be recorded next by using the control transmitter) To stop recording Recording CD(s) on both sides of a tape automatically Automatic tape-editing Page To record programmed tracks from one or more discs 2 Follow steps 3–6on page 3 Press the PROG button 4 If necessary, select a desired disc by pressing the DISC SKIP button 5 Select the desired track number by pressing the track number input buttons Recording from the built-intuner Dubbing Erasing recorded tapes Timer play ➂ At ON TIME/time setting mode TIME ADJ TIMER HOUR MINUTE ➃At OFF TIME/time setting mode To cancel the timer play setting Timer recording (To record a tuner program) Sleep timer operation Using the timer and the sleep timer at the same time <U.S.A., Canada, Australia, Singapore and General models <U.K. and Europe models Internal care External care TROUBLESHOOTING SPECIFICATIONS