Manuals / Brands / Home Audio / Speaker System / Yamaha / Home Audio / Speaker System

Yamaha CC-75 Automatic tuning, Manual tuning, English, TUNING OPERATION, “MW/LW” is for U.K. and Europe models, (In this mode, stations are received in monaural.)

1 54

Download 54 pages, 933.68 Kb

TUNING OPERATION

1

3, 2

Receiver

4, 3

2

CD

1	2	3	4	5
1	2	3	4	5
6	7	8
6	7	8	9	0
A	B	C	D	E
TIME	PROG	TAPE	EDIT	+10
REPEAT	RANDOM	STOP	PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP		TUNER	1
PLAY	STOP PLAY
		TAPE
DECK
A/B	REC/PAUSE	INPUT
EFFECT LEVEL	SP/PHONES MODE	DSS

-+

POWER SLEEP DISPLAY	VOLUME
	-	+

“AM” is for U.S.A., Canada, Australia, Singapore and General models.“MW/LW” is for U.K. and Europe models.

Normally, if station signals are strong and there is no interference, quick automatic-search tuning (Automatic tuning) is possible. However, if signals of the station you want to select are weak, you must tune to it manually (Manual tuning).

Automatic tuning

1 Select the TUNER position with the INPUT SELECTOR control, watching the display.

2 Select the reception band [FM or AM (MW or LW)] by pressing the BAND button while watching the display.

3 Press the AUTO/MAN’L button so that “AUTO TUNING” appears on the display.(In this mode, stations are received in stereo or monaural automatically.)

4 Press the TUNING UP button to tune to a higher frequency, or press the TUNING DOWN button to tune to a lower frequency.

(When tuned to a station, “TUNED” will light up on the display.)

5 If the station where tuning search stopped is not the desired one, follow step 4 again.

*If the tuning search does not stop at the desired station, change to the Manual tuning method as described below.

*STEREO indicator will light up when an FM stereo broadcast with sufficient signal strength is received.

Manual tuning

1 Follow steps 1 and 2 of the Automatic tuning method.

2 Press the AUTO/MAN’L button so that “AUTO TUNING” disappears from the display.

(In this mode, stations are received in monaural.)

3 Press and hold the TUNING UP button to tune to a higher frequency, or press and hold the TUNING DOWN button to tune to a lower frequency.

Release it just before reaching the desired frequency, and then press it repeatedly until the desired frequency appears.

(When tuned to a station, “TUNED” will light up on the display.)

Note

If you tune to an FM station manually, it is received in monaural automatically to increase the signal quality.

English

E-19

Contents

Page ●After unpacking, check that the following parts are contained ●Après le déballage, vérifier que les pièces suivantes sont incluses ●Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind ●Kontrollera efter det apparaten packats upp att följande delar finns med ●Controleer na het uitpakken of de volgende onderdelen voorhanden zijn 1CDC-S75 2RX-S75 EFG H WX Y H 3KXW-S75 cd e f g h ij 4 NX-S75 HIJK L To AC outlet Vers la prise c.a Zur Netzsteckdose Till nätuttag Alla presa AC INTRODUCTION English FEATURES •75W + 75W (6Ω) Output Power, 10% THD, 1 kHz •Random Access Programmable CD Playback PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT ■Do not operate this unit upside-down.It may overheat, possibly causing damage ■Never open the cabinet. If something drops into the set, contact your dealer Condensation can cause the unit to malfunction. To eliminate condensation: •CD pickup SETTING UP THE SYSTEM Setup examples KXW-S75 RX-S75 CDC-S75 (See figure 1 and 2 on page 3 – 5 at the beginning part of this manual.) 1Disc Table 2Stop Button: 3Disc Selector Buttons 4TIME Button Names of control buttons (See figure 5 on page 7 at the beginning part of this manual.) 1Remote Control Transmitter Window 2Preset Station Number Buttons 3A, B, C, D, E Selector Buttons Loading the batteries for the remote control transmitter (See figure 6 on page 7.) (See figure 8 on page 8.) Proper use of the remote control transmitter (See figure 7 on page 7.) Antenna connection Speaker connection System connection (See figure 0 on page 8.) Connecting the AC supply lead (See figure A on page 8.) SETTING THE CLOCK Changes Minute Second 2 While pressing the TIME ADJ button, press the HOUR button and set the hour The hour setting will not advance even if minute is advanced from “59” to “00” Volume Balance Tone Listening to the music with the DSS Care of compact discs CD playback Direct-selectionplay Skip search Manual search Program play To stop program play •Press the stop button. The first programmed track number will be displayed To resume playback, press the play/pause To cancel a programmed sequence There are several methods as described below Repeat play Random play Switching the time display Automatic tuning Manual tuning Preset tuning Automatic preset tuning Displaying RDS data To turn the unit into the RDS mode Calling a preset RDS station by the program type (PTY SEEK) Other functions which make use of RDS data service General information Tape A or tape B playback Winding the tape Searching for the beginning of a desired selection Continuous playback CD synchronized recording To stop recording temporarily 1 Press the stop button of the CD player 2 Choose the selection to be recorded next by using the control transmitter) To stop recording Recording CD(s) on both sides of a tape automatically Automatic tape-editing Page To record programmed tracks from one or more discs 2 Follow steps 3–6on page 3 Press the PROG button 4 If necessary, select a desired disc by pressing the DISC SKIP button 5 Select the desired track number by pressing the track number input buttons Recording from the built-intuner Dubbing Erasing recorded tapes Timer play ➂ At ON TIME/time setting mode TIME ADJ TIMER HOUR MINUTE ➃At OFF TIME/time setting mode To cancel the timer play setting Timer recording (To record a tuner program) Sleep timer operation Using the timer and the sleep timer at the same time <U.S.A., Canada, Australia, Singapore and General models <U.K. and Europe models Internal care External care TROUBLESHOOTING SPECIFICATIONS