Manuals / Brands / Home Audio / Speaker System / Yamaha / Home Audio / Speaker System

Yamaha CC-75 Tape A or tape B playback, Receiver, Tape Deck, DECK A/B button, To stop playback, Direct operation, DECK A selector button, DECK B selector button

1 54

Download 54 pages, 933.68 Kb

TAPE DECK OPERATION

Receiver

1

DECK A selector buttonDECK B selector buttonTape Deck




2		5 6				6 4			2

	Tape A or tape B playback		English
	1	Select the TAPE position with the INPUT SELECTOR	English


		control, watching the display.
	2	Open the DECK A or DECK B cassette compartment by
		pressing the EJECT button.
	3	Load the tape into the DECK A or DECK B cassette
		compartment, and close the lid panel completely by
		pressing the upper part of the center of the panel as
		figured left.
		* If you have loaded two tapes into both the DECK A and
		B cassette compartments, select the DECK A or B in
		which the tape you want to play back is loaded by
		pressing the DECK A or B selector button.

4 Set the Dolby NR switch to B or C if the tape is recorded with Dolby noise reduction, and to OFF if Dolby NR is not used.

*For selection of the Dolby B or C position, refer to the “Dolby B and C Type Noise Reduction” on page 29.

5 Set the reverse MODE switch as desired.

The reverse MODE switch can be operated before or during playback, and changes tape playback as follows:

3

Side A only	Side A → Side
	B
Side B only	Side B only

Side A → Side B

(Repeats 8 times) Starts from side A.

Side A → Side B

(Repeats 8 times) Starts from side B. (Side A is not played at the first time.)

6 Press the play button to listen to side A, or the

play button for side B.

To stop playback

Press the stop button.

Note

When removing the tape, press the stop button, and then open the cassette compartment.

6

DECK A/B button

CD

1	2	3	4	5
1	2	3	4	5
6	7	8
6	7	8	9	0
A	B	C	D	E
TIME	PROG	TAPE	EDIT	+10

REPEAT RANDOM STOP PLAY/PAUSE OPEN/CLOSE

MODE DISC SKIP		TUNER
PLAY	STOP PLAY
		TAPE
DECK
A/B	REC/PAUSE	INPUT
EFFECT LEVEL	SP/PHONES MODE	DSS

-+

POWER SLEEP DISPLAY	VOLUME
	-	+

6

1

Direct operation

Even if an input source other than tape deck is selected, pressing the play button (or the fast wind button) will start playback (or fast winding) directly.

E-27

Contents

Page ●After unpacking, check that the following parts are contained ●Après le déballage, vérifier que les pièces suivantes sont incluses ●Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind ●Kontrollera efter det apparaten packats upp att följande delar finns med ●Controleer na het uitpakken of de volgende onderdelen voorhanden zijn 1CDC-S75 2RX-S75 EFG H WX Y H 3KXW-S75 cd e f g h ij 4 NX-S75 HIJK L To AC outlet Vers la prise c.a Zur Netzsteckdose Till nätuttag Alla presa AC INTRODUCTION English FEATURES •75W + 75W (6Ω) Output Power, 10% THD, 1 kHz •Random Access Programmable CD Playback PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT ■Do not operate this unit upside-down.It may overheat, possibly causing damage ■Never open the cabinet. If something drops into the set, contact your dealer Condensation can cause the unit to malfunction. To eliminate condensation: •CD pickup SETTING UP THE SYSTEM Setup examples KXW-S75 RX-S75 CDC-S75 (See figure 1 and 2 on page 3 – 5 at the beginning part of this manual.) 1Disc Table 2Stop Button: 3Disc Selector Buttons 4TIME Button Names of control buttons (See figure 5 on page 7 at the beginning part of this manual.) 1Remote Control Transmitter Window 2Preset Station Number Buttons 3A, B, C, D, E Selector Buttons Loading the batteries for the remote control transmitter (See figure 6 on page 7.) (See figure 8 on page 8.) Proper use of the remote control transmitter (See figure 7 on page 7.) Antenna connection Speaker connection System connection (See figure 0 on page 8.) Connecting the AC supply lead (See figure A on page 8.) SETTING THE CLOCK Changes Minute Second 2 While pressing the TIME ADJ button, press the HOUR button and set the hour The hour setting will not advance even if minute is advanced from “59” to “00” Volume Balance Tone Listening to the music with the DSS Care of compact discs CD playback Direct-selectionplay Skip search Manual search Program play To stop program play •Press the stop button. The first programmed track number will be displayed To resume playback, press the play/pause To cancel a programmed sequence There are several methods as described below Repeat play Random play Switching the time display Automatic tuning Manual tuning Preset tuning Automatic preset tuning Displaying RDS data To turn the unit into the RDS mode Calling a preset RDS station by the program type (PTY SEEK) Other functions which make use of RDS data service General information Tape A or tape B playback Winding the tape Searching for the beginning of a desired selection Continuous playback CD synchronized recording To stop recording temporarily 1 Press the stop button of the CD player 2 Choose the selection to be recorded next by using the control transmitter) To stop recording Recording CD(s) on both sides of a tape automatically Automatic tape-editing Page To record programmed tracks from one or more discs 2 Follow steps 3–6on page 3 Press the PROG button 4 If necessary, select a desired disc by pressing the DISC SKIP button 5 Select the desired track number by pressing the track number input buttons Recording from the built-intuner Dubbing Erasing recorded tapes Timer play ➂ At ON TIME/time setting mode TIME ADJ TIMER HOUR MINUTE ➃At OFF TIME/time setting mode To cancel the timer play setting Timer recording (To record a tuner program) Sleep timer operation Using the timer and the sleep timer at the same time <U.S.A., Canada, Australia, Singapore and General models <U.K. and Europe models Internal care External care TROUBLESHOOTING SPECIFICATIONS