Manuals / Brands / Home Audio / Speaker System / Yamaha / Home Audio / Speaker System

Yamaha CC-75 English, SETTING THE CLOCK, Note, Changes, Minute Second, To reset the second to “00”, To display the time by “second”

1 54

Download 54 pages, 933.68 Kb

SETTING THE CLOCK

1

DISPLAY

	2	TUNING
	MEMORY	DOWN	UP
	TIME ADJ	HOUR	MINUTE
	3		Changes.
	3	TUNING
		TUNING
	MEMORY	DOWN	UP
	TIME ADJ	HOUR	MINUTE

Changes.

AUTO/MAN'L

SEC

Minute Second

1 While the power is on, press the DISPLAY button to display the time. If the power is off, you can proceed to the next step.

2 While pressing the TIME ADJ button, press the HOUR button and set the hour.

*Press the HOUR button once to advance the time by 1 hour. Press and hold to advance continuously.

3 While pressing the TIME ADJ button, press the MINUTE button and set the minute.

*Press the MINUTE button once to advance the time by 1 minute. Press and hold to advance continuously.

*The hour setting will not advance even if minute is advanced from “59” to “00”.

To display the time by “second”

While pressing the SEC button, the current time is displayed by minute and second.

To reset the second to “00”While pressing the SEC button, press the TIME ADJ button.*If the current second is lower than 30, it is reset to 00.

*If the current second is higher than 30, the minute is advanced by 1 minute and the second is reset to 00.

(If the current minute is “59”, in this case, the hour is also advanced by 1 hour.)

In the event of a power failure or when the AC supply lead is disconnected.

The time display will go out, however, the clock will function for about 5 minutes without power supply. So you do not have to reset the time if the AC power supply is resumed within about 5 minutes.

When the AC power supply is resumed after more than 5 minutes pass without power supply, the time display will flash on and off to indicate that the time must be reset.

Note

If this system is left for several minutes without setting the time after the AC power lead of this system is connected to the AC outlet, there may be a case that the display is turned into a demonstration mode. (This mode is virtually unnecessary for using this system.)

In this case, first turn the power on by pressing the POWER switch to cancel the mode, and then set the time.

English

E-9

Contents

Page ●After unpacking, check that the following parts are contained ●Après le déballage, vérifier que les pièces suivantes sont incluses ●Nach dem Auspacken überprüfen, ob die folgenden Teile vorhanden sind ●Kontrollera efter det apparaten packats upp att följande delar finns med ●Controleer na het uitpakken of de volgende onderdelen voorhanden zijn 1CDC-S75 2RX-S75 EFG H WX Y H 3KXW-S75 cd e f g h ij 4 NX-S75 HIJK L To AC outlet Vers la prise c.a Zur Netzsteckdose Till nätuttag Alla presa AC INTRODUCTION English FEATURES •75W + 75W (6Ω) Output Power, 10% THD, 1 kHz •Random Access Programmable CD Playback PRECAUTIONS: READ THIS BEFORE OPERATING YOUR UNIT ■Do not operate this unit upside-down.It may overheat, possibly causing damage ■Never open the cabinet. If something drops into the set, contact your dealer Condensation can cause the unit to malfunction. To eliminate condensation: •CD pickup SETTING UP THE SYSTEM Setup examples KXW-S75 RX-S75 CDC-S75 (See figure 1 and 2 on page 3 – 5 at the beginning part of this manual.) 1Disc Table 2Stop Button: 3Disc Selector Buttons 4TIME Button Names of control buttons (See figure 5 on page 7 at the beginning part of this manual.) 1Remote Control Transmitter Window 2Preset Station Number Buttons 3A, B, C, D, E Selector Buttons Loading the batteries for the remote control transmitter (See figure 6 on page 7.) (See figure 8 on page 8.) Proper use of the remote control transmitter (See figure 7 on page 7.) Antenna connection Speaker connection System connection (See figure 0 on page 8.) Connecting the AC supply lead (See figure A on page 8.) SETTING THE CLOCK Changes Minute Second 2 While pressing the TIME ADJ button, press the HOUR button and set the hour The hour setting will not advance even if minute is advanced from “59” to “00” Volume Balance Tone Listening to the music with the DSS Care of compact discs CD playback Direct-selectionplay Skip search Manual search Program play To stop program play •Press the stop button. The first programmed track number will be displayed To resume playback, press the play/pause To cancel a programmed sequence There are several methods as described below Repeat play Random play Switching the time display Automatic tuning Manual tuning Preset tuning Automatic preset tuning Displaying RDS data To turn the unit into the RDS mode Calling a preset RDS station by the program type (PTY SEEK) Other functions which make use of RDS data service General information Tape A or tape B playback Winding the tape Searching for the beginning of a desired selection Continuous playback CD synchronized recording To stop recording temporarily 1 Press the stop button of the CD player 2 Choose the selection to be recorded next by using the control transmitter) To stop recording Recording CD(s) on both sides of a tape automatically Automatic tape-editing Page To record programmed tracks from one or more discs 2 Follow steps 3–6on page 3 Press the PROG button 4 If necessary, select a desired disc by pressing the DISC SKIP button 5 Select the desired track number by pressing the track number input buttons Recording from the built-intuner Dubbing Erasing recorded tapes Timer play ➂ At ON TIME/time setting mode TIME ADJ TIMER HOUR MINUTE ➃At OFF TIME/time setting mode To cancel the timer play setting Timer recording (To record a tuner program) Sleep timer operation Using the timer and the sleep timer at the same time <U.S.A., Canada, Australia, Singapore and General models <U.K. and Europe models Internal care External care TROUBLESHOOTING SPECIFICATIONS