Connecting to computer devices, For US model only | Yamaha DPX-1200

Connecting to computer devices

You can use the following two methods to connect to computer devices. Be sure to use cables with jacks that match the connectors and jacks you wish to use. You cannot use a HDMI-DVI conversion cable to connect this unit and a computer device.

Input		Signal type			Connector type
INPUT A		RGB (Analog)		BNC jack x 5
INPUT B		RGB (Analog)		D-sub 15 pin
		OUT		IN
	HDMI		REMOTE	RS-232C	TRIGGER OUT
INPUT B		INPUT A
RGB/YPBPR/YCBCR	D4 VIDEO	G/YB/PB/CBR/PR/CRHD/SYNCVD		S VIDEO	VIDEO

BNC monitor cable

D-Sub monitor cable

Monitor output terminal

Computer devices

Information for installers

(for US model only)

9

Connection

+polarity (inside)

-polarity (outside) (GND)

- polarity

+polarity

Use the supplied trigger-out DC plug to control external components.

Be sure to solder the wires from an external component to the plug terminals with the correct polarities, as illustrated at left.

Warning

•Soldering the wires to terminals with incorrect polarity may cause bodily injury or may damage this unit and the external component connected to this unit with this cable.

49

Image 53

Yamaha DPX-1200 manual Connecting to computer devices, Information for installers, For US model only, Input Signal type

Contents

DPX-1200 Alleen voor klanten in Nederland Important Safety Instructions FCC Information for US customers only We Want You Listening For a Lifetime Iii Table of contents Accessory check Inappropriate places for installation Features Main unit Front panel and controls Main unit Rear panel / Connections Remote control functions Remote control code switch Light switchRemote control cable jack Hide button Using the remote control with a wired connection Loading the batteries into the remote control Use within a left/right arc of 30 degrees Limits for using the remote controlDistance to sensor Angle to sensor Preparation If you have not installed the main unit or screen Prepararion Pre-operation check Checking installation and connectionsProjection preparations complete Main unit Turning the power on Turning the projector power on Lamp may blink when half lit. This is not a defect Placing the DPX-1200 in standby modeMemo Press the STANDBY/ON button Projection image signal Selecting an input signalSelecting using the Input button Press the + button to open the submenu Using the Input button to select a signalButton Aspect Input button Press the Aspect button Selecting a display aspect for a projection imageRemote cotrol Button Display aspect types Representative examples Input signal typeInput imageDisplay aspectProjected image Adjusting the vertical position V.POS button Adjusting the imagePattern button Crosshatch pattern Grayscale pattern Color bar pattern Zoom Menu screen Menu configurations Advanced Mode Basic ModeMenu items Menu item list Lower level menu items Submenu Items Menu group items and functions Saturation HueColor Temp White Correction Level Adjustment Color AdjustmentWhite Peaking Iris Signal Sync Adjustment Setup Level HdtvSignal Status Tracking Initial Setup Remote Control Reset button Remote control onlyMenu operations Operation button functions Press the Menu button to open Menu operations 1 with no submenuPress the + or button to select a menu group Menu Button Setting method depends on the item selected Press the + or button to select a suitable settingRemote Control Main Unit Menu Button Remote Control Main Unit Press the + button to move to Submenu Press the h or g button to to adjust item settingsMenu operations 2 with submenus See page 27 for datails about each color item Special menu operations Changing the position of the menu screen Resetting the selected parameterResetting all parameters Subtitle Zoom Resetting the lamp running time Press the button Changing the Gamma Example Using the inline menu Adjusting image quality using the inline menuInline menu composition Inline menu item list Saving memory settings Memory configurationsUsing the remote control Using the menu Press the g button to select Settings in the selected memoryBottom of the screen Press the h or g button to select Memory number Deactivating Memory Lock Setting Memory LockMemory lock Copy source Memory copyRecall the memory number to be Press Button Press the + button to display the confirmation screen Initialization of currently selected memory Resetting to the default settings Press Button to reset Parameters to their default Settings To reset all parameters for all memory numbers Input Signal type Connector type Connecting to AV componentsSub monitor cable BNC cable for Component connection Pin/BNC Video cable Adapters Pin cable Information for installers Connecting to computer devicesInput Signal type For US model only Mounting the projector on the ceiling Setting up the DPX-1200Mounting the projector on a table Projection distance When using a 169 screenWhen using a 43 screen Using Zoom to adjust image position Keystone adjustmentUsing V.POS vertical position to adjust image position Using the adjusters to adjust image position Glossary Tracking Test patternVista size Pulldown detection style IP conversion Signal type Active Fsc Color system Lines MHz Compatible signal typesSignal type Active Pixels Lines KHz Signal type Active Component type Pixels Lines KHz Replacing the filter MaintenanceRegular care Lamp cover screws Replacing the lampLoosen the lamp cover screws To protect the lamp, you cannot turn on Troubleshooting Troubleshooting Message Condition Message display LED indicator State Meaning LED indicator meanings Optical SpecificationsControls General 119.1 Dimensional drawing C2004 All Rights Reserved