Yamaha DPX-1200 Placing the DPX-1200 in standby mode

14

1. Press the STANDBY/ON button.

A confirmation message appears on the

screen.

◆Placing the DPX-1200 in standby mode

2. If you wish to place the DPX-1200

in standby mode, press the

STANDBY/ON button again.

The lamp changes to a half lit state, and the

fan activates for 2 minutes to cool the lamp.

During this time, the STANDBY/ON

indicator blinks orange, and pressing

STANDBY/ON does not turn main unit

power on again. When the unit finishes

cooling, the fan stops, and the STANDBY/

ON indicator turns orange.

Memo

•The lamp may blink when half lit. This is not a defect.

Warning

•Do not remove the power cable while the STANDBY/ON indicator is blinking green

or when the fan is activated. This could damage the lamp or reduce lamp life.

•If you do not plan to use the main unit for a long period of time, attach the lens cap

and remove the plug from the AC outlet.

•Condensation may appear on the unit if the temperature of the surrounding

environment changes quickly. Condensation may also cause the projected image to

be cloudy. Place the unit in standby mode until the condensation disappears.

Switching the unit on when condensation is present may damage the unit.

Turning the projector power on

AC inlet

Press again to enter standby.

HDMI

G/Y B/PB/CBR/PR/CR

INPUT A

HD/SYNC VD

OUT IN

REMOTE TRIGGER OUT

S-VIDEO VIDEO

INPUT B

RGB/YPBPR/YCBCR

RS-232C

D4 VIDEO

INPUT

MENU

PATTIRIS

AUTO

SETTING

ASPECT

ZOOM FOCUSV. POS

ESCAPE

STANDBY

/

ON

SETTING

LAMP COVER TEMP FAN

PATTERN

ESCAPE MENU

INPUT

ASPECT

Remote Control Main unit

button STANDBY/ON button

12_DPX-1100_E.p65 11/26/04, 1:47 PM14

Contents

Main DPX-1200 IMPORTANT! IMPORTANT SAFETY INSTRUCTIONS i Dimensional drawing 63 We Want You Listening For A Lifetime COMPLIANCE INFORMATION STATEMENT ii Caution: Read this before operating this unit. Installation Operation Others For U.K. customers Table of contents Inappropriate places for installation 1. Places where the temperature and humidity vary greatly 2. Places without adequate ventilation 3. Places where it gets dusty 1Getting started Features 2Features Main unit <Front panel and controls> 3Controls and functions Controls and functions 3 wer q 8 765432190 Main unit <Rear panel / Connections> 4Remote control Remote control 7 iINPUT button oLIGHT switch pHIDE button Loading the batteries into the remote control 11_DPX-1100_E.p65 11/26/04, 2:07 PM8 MENU INPUT LIGHT 4 Remote control 11_DPX-1100_E.p65 11/26/04, 2:07 PM9 Use within a left/right arc of 30 degrees Use within a vertical arc of 30 degrees Distance to sensor Angle to sensor STEP2 5 STEP 1 STEP2 Preparation Prepararion Step2 Connect an AV component or computer Turn the power on and selecting an image for projection Step1 Set up the projector and screen Checking installation and connections Pre-operation check Check installation and connections Select an image for projection and image adjustment Projection preparations complete Turn on the projector power. Turning the projector power on ON SETTING ESCAPE MENU STANDBY/ON indicator Placing the DPX-1200 in standby mode Turning the projector power on Selecting using the INPUT button Projection image signal Selecting an input signal INPUT SIGNAL 16 <Using the INPUT button to select a signal> + button 1. Press the INPUT button. The input signal selection menu appears on the display. 2. Use the h or g buttons to select an input signal, then press the button. Selecting a display aspect for a projection image button cursor button Remote cotrol Main unit ASPECT 18 <Display aspect types> Auto Normal Squeeze 19 <Representative examples> Select an image for projection Adjusting the vertical position V.POS button Adjusting the image Adjusting the image Adjusting the size of an image ZOOM button Adjusting the image focus FOCUS button Adjusting the iris setting IRIS button Menu configurations 13_DPX-1100_E.p65 11/26/04, 1:54 PM22 <Display example: [Color Adjustment] item submenu> White Peaking Iris Menu items 24 <Submenu Items> <Lower level menu items> 25 Menu group items and functions <Image> Black Level Contrast Gamma 26 Hue Color Temp. Sharpness Type Sharpness Gain 27 Color Adjustment Iris Level Adjustment White Peaking Signal Display Aspect Ratio Overscan 3D Y/C Separation Noise Reduction Page Initial 31 Setup Location Keystone Correction Remote Control Sensor Remote Control ID Menu operations Operation button functions 1Menu Button 2Cursor button 3 button Menu operations 1 (with no submenu) 13_DPX-1100_E.p65 11/26/04, 1:54 PM33 Menu operations use the procedure below to adjust menu item without submenus. 1. Press the MENU button to open the menu screen. Menu items related to the selected menu group are displayed. You can now adjust the selected item. 6. To close the menu screen when you have finished making adjustments, press the MENU button. 5. Move to another item or group as necessary. 13_DPX-1100_E.p65 11/26/04, 1:54 PM34 The setting method depends on the item selected. ESCAPE Button Menu operations 2 (with submenus) 36 <Color Adjustment> Special menu operations 37 <Resetting the selected parameter> <Resetting all parameters> <Changing the position of the menu screen.> 38 <Resetting the lamp running time.> <Subtitle Zoom> 39 13_DPX-1100_E.p65 11/26/04, 1:54 PM39 Press the button Press the h or g button to move to a different menu item in the [Subtitle Zoom] menu. 8. Press the ESCAPE button to return to the higher level selection menu. Adjusting image quality using the inline menu For PC type sources <Inline menu composition> Black Level <Example: Using the inline menu> 8Memory function (Save, Recall, Lock, Copy, Reset) 2. Press the g button to select Memory number status from the bottom of the screen. 5. Press the button to recall the settings in the selected memory. 4. Press the h or g button to select a memory number. 43 Memory lock 13_DPX-1100_E.p65 11/26/04, 1:54 PM43 disappears <Setting Memory Lock> <Deactivating Memory Lock> Memory copy 13_DPX-1100_E.p65 11/26/04, 1:54 PM44 Image Signal Initial Setup : Fix Memory 2 Page 46 Resetting to the default settings <Initialization of currently selected memory> 47 <To reset all parameters for all memory numbers> Connecting to AV components 9Connection 9 Connection + Connecting to computer devices Information for installers (for US model only) + - - 50 Setting up the DPX-1200 10 Mounting the projector on a table A: From in front of a screen B: From behind a screen (using a semi-translucent screen) Projection distance <When using a 4:3 screen> <When using a 16:9 screen> 52 <Using ZOOM to adjust image position> Projection image position Keystone adjustment Glossary 11 Reference Ceiling mount bracket Cinemascope size Test pattern Tracking Vista size 3-2 pulldown detection style IP conversion Glossary Compatible signal types Regular care Replacing the filter Maintenance Replacing the lamp Maintenance Troubleshooting Troubleshooting Message display LED indicator meanings Specifications Controls General Input Optical Dimensional drawing 63