Limits for using the remote control | Yamaha DPX-1300 specs

◆Limits for using the remote control

Use the remote control within the following parameters. The remote control may not function correctly if you use it outside the limits described here.

Distance to sensor

Angle to sensor

7 m

30˚ vertically and horizontally

(approximate value)

Use within a left/right arc of 30 degrees

Use within a vertical arc of 30 degrees

Warning

•Bright or fluorescent light on the main unit remote sensor may inhibit the functioning of the remote control.

•Objects placed between the main unit remote sensor and the remote control may block the remote control signal and inhibit functioning.

Remote control

English

Page 13

Image 13

Yamaha DPX-1300 manual Limits for using the remote control, Distance to sensor Angle to sensor

Contents

DPX-1300 Important Safety Instructions FCC Information for US customers only We Want You Listening For a Lifetime Iii Table of contents Accessory check Inappropriate places for installation Features English Features Main unit Front panel and controls Controls and functions Main unit Rear panel / Connections Remote control functions Light switch Remote control EnglishRemote control code switch Remote control cable jack Using the remote control with a wired connection Loading the batteries into the remote control Distance to sensor Angle to sensor Limits for using the remote controlUse within a left/right arc of 30 degrees Preparation If you have not installed the main unit or screen Prepararion Turn the power on and selecting an image for projection Mounting the projector on a table Setting up the DPX-1300Mounting the projector on the ceiling When using a 169 screen InstallationWhen using a 43 screen Projection distance Using Zoom to adjust image position Keystone adjustmentUsing V.POS vertical position to adjust image position Using the adjusters to adjust image position Connection Connecting to AV components Information for installers Connecting to computer devicesFor US model only + polarity inside Polarity outside GND Pre-operation check Checking installation and connectionsProjection English Projection preparations complete Turning the power on Turning the projector power onPress the STANDBY/ON button Button on the remote control Lamp may blink when half lit. This is not a defect Placing the DPX-1300 in standby modePress the STANDBY/ON button Selecting using the Input button Selecting an input signalProjection image signal Projection Using the Input button to select a signalPress the + button to open the submenu Press the Aspect button Selecting a display aspect for a projection imageRemote cotrol Display aspect types Representative examples Input signal typeInput imageDisplay aspectProjected image Adjusting the vertical position V.POS button Adjusting the imagePattern button Crosshatch pattern Grayscale pattern Color bar pattern Adjusting the size of an image Zoom button Menu screen Menu configurations Menu item list Menu items Lower level menu items Submenu Items Menu group items and functions Menu Adjusts the iris Optical Level AdjustmentAdjusts the analog input signal gain and offset settings White Peaking Menu English Signal Signal Status Signal LevelOvershoot Supp. Range Overshoot Supp. Level Initial Setup Message Menu ColorTrigger Out Baud Rate Remote Control Reset button Remote control onlyMenu operations Operation button functions Press the Menu button to open Menu operations 1 with no submenuMenu screen Press the + or button to select a menu group Setting method depends on the item selected Press the + or button to select a suitable settingRemote Control Main Unit Menu Button Remote Control Main Unit Menu operations 2 with submenus Press the h or g button to adjust item settingsPress the + button to move to the submenu Appears to the right of items that contain a submenu See page 32 for datails about each color item Special operations Example Color temperature fixed mode Example Using the color temperature fixed modeName of the selected item appears here Resetting all the settings Resetting the selected settingsChanging the position of the menu screen Subtitle Zoom Resetting the lamp running time Press the button Changing the Gamma Example Using the inline menu Adjusting image quality using the inline menuInline menu composition Inline menu item list Saving memory settings Memory configurationsUsing the remote control Using the menu Press the g button to select Memory number status from Memory function EnglishBottom of the screen Press the h or g button to select a memory number Memory lock Setting Memory LockDeactivating Memory Lock Select the memory number you Recall the memory number to be Memory copyCopy source Press the g button to select Press the + button to display the confirmation screen Initialization of the currently selected memory Resetting to the default settings in the memory menu Initialization of all the memories Reference Glossary Compatible signal types Reference English Signal type Active Component type Pixels Lines KHz Regular care MaintenanceReplacing the filter Loosen the lamp cover screws Replacing the lampLamp cover screws To protect the lamp, you cannot turn on Troubleshooting Troubleshooting Message Condition Message display LED indicator State Meaning LED indicator meanings Optical SpecificationsControls General 119.1 Dimensional drawing C2005 All Rights Reserved